- 您現在的位置：買賣IC網 > PDF目錄1976 > XR20V2170IL40-F (Exar Corporation)IC UART/TXRX I2C/SPI RS232 40QFN PDF資料下載
參數資料
| 型號： | XR20V2170IL40-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 25/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART/TXRX I2C/SPI RS232 40QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 64 字節 |
| 規程： | RS232 |
| 電源電壓： | 2.97 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN 裸露焊盤（6x6） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1478 XR20V2170IL40-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
XR20V2170
31
REV. 1.0.1
I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
TCR[3:0]: RX FIFO Halt Level
A value of 0-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the Halt Level. When the RX
FIFO is greater than or equal to this value, the RTS# output will be de-asserted if Auto RTS flow control is used
or the XOFF character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that
this value is greater than the RX Trigger Level.
TCR[7:4]: RX FIFO Resume Level
A value of 0-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the Resume Level. When the
RX FIFO is less than or equal to this value, the RTS# output will be re-asserted if Auto RTS flow control is used
or the XON character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that this
value is less than the RX Trigger Level.
4.12
Trigger Level Register (TLR) - Read/Write (requires EFR bit-4 = 1)
This register replaces SPR and is accessible under the conditions listed in Table 13. This 8-bit register is used
to store the RX and TX FIFO trigger levels used for interrupts.
TLR[3:0]: TX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the TX FIFO Trigger Level.
When the number of available spaces in the TX FIFO is greater than or equal to this value, a Transmit Ready
interrupt is generated. For any non-zero value, TCR[3:0] will be used as the TX FIFO Trigger Level. If
TCR[3:0] = 0x0, then the TX FIFO Trigger Level is the value selected by FCR[5:4]. See Table 10.
TLR[7:4]: RX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the RX FIFO Trigger Level.
When the number of characters received in the RX FIFO is greater than or equal to this value, a Receive Data
Ready interrupt is generated (a Receive Data Timeout interrupt is independent of the RX FIFO Trigger Level
and can be generated any time there is at least 1 byte in the RX FIFO and the RX input has been idle for the
timeout period described in “Section 2.9, Receiver” on page 13). For any non-zero value, TCR[7:4] will be
used as the RX FIFO Trigger Level. If TCR[7:4] = 0x0, then the RX FIFO Trigger Level is the value selected by
FCR[7:6]. See Table 10.
4.13
Transmit FIFO Level Register (TXLVL) - Read-only
This register reports the number of spaces available in the TX FIFO. If the TX FIFO is empty, the TXLVL
register will report that there are 64 spaces available. If the TX FIFO is full, the TXLVL register will report that
there are 0 spaces available.
4.14
Receive FIFO Level Register (RXLVL) - Read-only
This register reports the number of characters available in the RX FIFO. If the RX FIFO is empty, the RXLVL
register will report that there are 0 characters available. If the RX FIFO is full, the RXLVL register will report
that there are 64 characcters available.
4.15
GPIO Direction Register (IODir) - Read/Write
This register is used to program the direction of the GPIO pins.
IODir[7:4]: Set up DTR#, DSR#, CD#, RI#
For normal operation, these bits should be set to ’0010’.
IODir[3:0]: GPIO3 to GPIO0 I/O Direction Control
Logic 0 = set GPIO pin as input
Logic 1 = set GPIO pin as output
相關PDF資料 |
PDF描述 |
|---|---|
| XR20V2172IL64-F | IC UART/TXRX I2C/SPI RS232 64QFN |
| XR21V1410IL16TR-F | IC USB UART FIFO FULL SPD 16QFN |
| XR21V1412IL32TR-F | IC USB UART FIFO FULL SPD 32QFN |
| XR21V1414IM48-F | IC UART FIFO USB QUAD 48TQFP |
| XR3178EID-F | IC TXRX RS485 DIFF 3V 8NSOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20V2170L40-0A-EB | 功能描述:界面開發工具 Supports V2170 40pin QFN,I2C Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR20V2170L40-0B-EB | 功能描述:UART 接口集成電路 Supports V2170 40pin QFN,SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20V2172 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
| XR20V2172_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
| XR20V2172IL64 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。