- 您現在的位置：買賣IC網 > PDF目錄16820 > XR17V358IB-E8-EVB (Exar Corporation)EVAL BOARD FOR XR17V358-E8 PDF資料下載
參數資料
| 型號： | XR17V358IB-E8-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 53/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR17V358-E8 |
| 產品培訓模塊： | PCIe UARTs UART Product Overview |
| 標準包裝： | 1 |
| 主要目的： | 接口，UART |
| 嵌入式： | 否 |
| 已用 IC / 零件： | XR17V358 |
| 已供物品： | 板 |
| 相關產品： | 1016-1294-ND - IC UART PCIE OCTAL 176FPBGA |
| 其它名稱： | 1016-1296 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
XR17V358
57
REV. 1.0.4
HIGH PERFORMANCE OCTAL PCI EXPRESS UART
LSR[3]: Receive Data Framing Error Flag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[2]: Receive Data Parity Error Flag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR (top of the FIFO) does not have correct parity
information and is suspect. This error is associated with the character available for reading in RHR.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
4.10
Modem Status Register (MSR) - Read Only
This register provides the current state of the modem interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register are used to indicate the changed information. These bits
are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general
purpose inputs/outputs when they are not used with modem signals.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit [3] in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
MSR[6]: RI Input Status
Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit [2] in the
MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[5]: DSR Input Status
DSR# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=1). Auto CTS/DSR flow control
allows starting and stopping of local data transmissions based on the modem DSR# signal. A HIGH on the
DSR# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW
will resume data transmission. Normally MSR bit [5] is the complement of the DSR# input. However in the
loopback mode, this bit is equivalent to the DTR# bit in the MCR register. The DSR# input may be used as a
general purpose input when the modem interface is not used.
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=0). Auto CTS/DSR flow control
allows starting and stopping of local data transmissions based on the modem CTS# signal. A HIGH on the
CTS# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW
will resume data transmission. Normally MSR bit [4] is the complement of the CTS# input. However in the
loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input may be used as a
general purpose input when the modem interface is not used.
相關PDF資料 |
PDF描述 |
|---|---|
| EBM24DCSH-S288 | CONN EDGECARD 48POS .156 EXTEND |
| EGM08DRST | CONN EDGECARD 16POS DIP .156 SLD |
| V150B28E150BL | CONVERTER MOD DC/DC 28V 150W |
| HSM06DRYH-S13 | CONN EDGECARD 12POS .156 EXTEND |
| EBM24DCSD-S288 | CONN EDGECARD 48POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR1857SN | 制造商:Electro-Term/Hollingsworth 功能描述: |
| XR1858SN | 制造商:Electro-Term/Hollingsworth 功能描述: |
| XR1859SN | 制造商:Electro-Term/Hollingsworth 功能描述: |
| XR1859SNT | 制造商:Hollingsworth 功能描述: |
| XR1880S | 制造商:Electro-Term/Hollingsworth 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。