參數資料
型號: XR17V252IM-F
廠商: Exar Corporation
文件頁數: 41/69頁
文件大?。?/td> 0K
描述: IC UART PCI BUS DUAL 100TQFP
標準包裝: 90
特點: *
通道數: 2,DUART
FIFO's: 64 字節
規程: RS485
電源電壓: 3.3V,5V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
安裝類型: 表面貼裝
封裝/外殼: 100-TQFP
供應商設備封裝: 100-TQFP(14x14)
包裝: 托盤
XR17V252
46
66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.2
LCR[1:0]: TX and RX Word Length Select
These two bits specify the word length to be transmitted or received.
5.8
Modem Control Register (MCR) - Read/Write
The MCR register is used for controlling the modem interface signals or general purpose inputs/outputs.
MCR[7]: Clock Prescaler Select (requires EFR bit [4]=1)
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
MCR[6]: Infrared Encoder/Decoder Enable (requires EFR bit [4]=1)
The state of this bit depends on the sampled logic level of pin ENIR during power up, following a hardware
reset (rising edge of RST# input). Afterward user can override this bit for desired operation.
Logic 0 = Enable the standard modem receive and transmit character interface.
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. While in this mode, the TX/RX output/
input are routed to the infrared encoder/decoder. The data input and output levels will conform to the IrDA
infrared interface requirement. As such, while in this mode the infrared TX output will be a LOW during idle
data conditions. FCTR bit [4] may be selected to invert the RX input signal level going to the decoder for
infrared modules that provide rather an inverted output.
MCR[5]: Xon-Any Enable (requires EFR bit [4]=1)
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode any RX character received will enable Xon, resume data
transmission.
MCR[4]: Internal Loopback Enable
Logic 1 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 14.
BIT [1]
BIT [0]
WORD LENGTH
0
5 (default)
0
1
6
1
0
7
1
8
相關PDF資料
PDF描述
MS3110E14-15S CONN RCPT 15POS WALL MNT W/SCKT
SCC2692AE1B44,557 IC UART DUAL W/FIFO 44PLCC
MS27467T13B4P CONN PLUG 4POS STRAIGHT W/PINS
MS27484T16F26S CONN PLUG 26POS STRAIGHT W/SCKT
SC26C92C1A,512 IC UART DUAL W/FIFO 44-PLCC
相關代理商/技術參數
參數描述
XR17V252IMTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 3.3V 100-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR17V252IMTR-F
XR17V254 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254_08 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254IV 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254IV-0A-EVB 功能描述:UART 接口集成電路 Supports V254 144 ld LQFP,PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel