參數資料
型號： XR17V252IM-F
廠商： Exar Corporation
文件頁數： 11/69頁
文件大?。?/td> 0K
描述： IC UART PCI BUS DUAL 100TQFP
標準包裝： 90
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS485
電源電壓： 3.3V，5V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 100-TQFP
供應商設備封裝： 100-TQFP（14x14）
包裝： 托盤
XR17V252
19
REV. 1.0.2
66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT
Timer Operation in Re-triggerable Mode:
In the re-triggerable mode, when the Timer is started, the Timer output will stay HIGH until it reaches half of the
terminal count N (= P clocks) and toggle LOW and stay LOW for a similar amount of time (Q clocks). The
above step will keep repeating until the Timer is stopped at which time the output will become HIGH (default
state). See Figure 7. Also, after the Timer is started, re-starting the Timer does not have any effect in re-
triggerable mode. The Timer must be programmed while it is stopped since the following operations are
blocked when the Timer is running:
■ Any write to TIMER MSB, LSB registers
■ Issue of any command other than ’Stop Timer’ and ’Reset Timer’ (’Start Timer’ is not allowed)
Routing the Timer Output to MPIO[0] Pin:
MPIO[0] pin is by default (on power up or reset, for example) an input. However, whenever the Timer output is
routed to MPIO[0] pin,
■ MPIO[0] will be automatically selected as an output
■ MPIO[0] will become HIGH (the default state of Timer output)
■ All MPIO control registers (MPIOLVL, MPIOSEL etc) lose control over MPIO[0] and get the control back
only when the Timer output is de-routed from MPIO[0].
Timer Interrupt
In the one-shot mode, the Timer will issue an interrupt upon timing out which is ’N’ clocks after the Timer is
started. In the re-triggerable mode, the Timer will keep issuing an interrupt every ’N’ clocks which is on every
rising edge of the Timer output. The Timer interrupt can be cleared by reading the TIMERCNTL register or
when a Timer Reset command is issued which brings the Timer back to its default settings. The TIMERCNTL
will read a value of 0x01 when the Timer interrupt is enabled and there is a pending interrupt. It reads a value
of 0x00 at all other times. Stopping the Timer does not clear the interrupt and neither does subsequent re-
starting.
FIGURE 7. TIMER OUTPUT IN ONE-SHOT AND RE-TRIGGERABLE MODES
TIMER Output in
Re-triggerable
Mode
TIMER Output in
One-Shot Mode
After 'P'
clocks
START TIMER
COMMAND ISSUED
START TIMER
COMMAND ISSUED
'N' Clocks
STOP TIMER
COMMAND ISSUED
START TIMER COMMANDS ISSUED: LESS THAN 'N'
CLOCKS BETWEEN SUCCESSIVE COMMANDS
< 'N' Clocks
After 'P'
clocks
After 'P'
clocks
After 'P'
clocks
After 'P'
clocks
After 'Q'
clocks
After 'Q'
clocks
After 'Q'
clocks
After 'Q'
clocks
< 'N' Clocks
相關PDF資料
PDF描述
MS3110E14-15S CONN RCPT 15POS WALL MNT W/SCKT
SCC2692AE1B44,557 IC UART DUAL W/FIFO 44PLCC
MS27467T13B4P CONN PLUG 4POS STRAIGHT W/PINS
MS27484T16F26S CONN PLUG 26POS STRAIGHT W/SCKT
SC26C92C1A,512 IC UART DUAL W/FIFO 44-PLCC
相關代理商/技術參數
參數描述
XR17V252IMTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 3.3V 100-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR17V252IMTR-F
XR17V254 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254_08 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254IV 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254IV-0A-EVB 功能描述:UART 接口集成電路 Supports V254 144 ld LQFP,PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*