Philips Semiconductors
Preliminary specification
XA-C3
XA 16-bit microcontroller family
32K/1024 OTP CAN transport layer controller
1 UART, 1 SPI Port, CAN 2.0B, 32 CAN ID filters, transport layer co-processor
2000 Jan 25
27
DC ELECTRICAL CHARACTERISTICS
Table 19. DC Electrical Characteristics
V
DD
= 4.5V to 5.5V unless otherwise specified;
T
ambient
= 0 to +70
°
C for commercial, –40
°
C to +85
°
C for industrial, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
TYP
UNIT
MIN
MAX
Supply Currents
I
DD
I
ID
I
PD
I
PDI
Inputs
V
RAM
V
IL
V
IH
V
IH1
V
OL
Supply current, operating mode
Supply current, Idle mode
Power–Down mode current
Power–Down mode current (–40
°
C to +85
°
C)
32 MHz
32 MHz
54
25
5
80
30
100
150
mA
mA
μ
A
μ
A
RAM keep–alive voltage
Input Low voltage
Input High voltage, except XTAL1, RST
/
Input High voltage to XTAL1, RST
/
Output Low voltage all ports, ALE, PSEN
/
3
RAM keep–alive voltage
1.5
–0.5
2.2
0.7V
DD
V
V
V
V
V
0.22V
DD
At 5.0V
At 5.0V
I
OL
= 3.2mA, V
DD
= 5.0V
I
OH
= –100mA,
V
DD
= 4.5V
I
OH
= 3.2mA, V
DD
= 4.5V
0.5
V
OH1
Output High voltage all ports, ALE, PSEN
/
1
2.4
V
V
OH2
C
IO
I
IL
I
LI
I
TL
CAN RxD
V
IL
V
IH
C
I
I
IL
I
LI
CAN TxD
V
OL
Output High voltage, ports P0–3, ALE, PSEN
/
2
Input/Output pin capacitance
Logical 0 Input current, P0–3
6
Input Leakage current, P0–3
5
Logical 1–to–0 Transition current –– all ports
4
2.4
V
pF
μ
A
μ
A
μ
A
15
–75
±
10
–650
V
IN
= 0.45V
V
IN
= V
IL
or V
IH
At 5.5V
–25
Input Low voltage
Input High voltage
Input pin capacitance
Logical 0 Input current
Input Leakage current
–0.5
2.2
0.22V
DD
V
V
pF
μ
A
μ
A
V
DD
= 5.0V
15
–75
±
10
V
IN
= 0.45V
V
IN
= V
IL
or V
IH
–25
Output Low voltage
I
OL
= 3.2mA, V
DD
= 5.0V
I
OH
= –100mA,
V
DD
= 4.5V
0.5
V
V
OH
Output High voltage
2.4
V
C
O
I
TL
Output capacitance
Logical 1–to–0 Transition current
15
–650
pF
μ
A
V
DD =
5.5V
NOTES:
1. Ports in Quasi–Bidirectional mode with weak pull–up (applies to ALE, PSEN
/
only during Reset operations).
2. Ports in Push–Pull mode, both pull–up and pull–down are assumed to be of the same strength
3. In all output modes
4. Port pins source a transition current when used in Quasi–Bidirectional mode and externally driven from 1 to 0. This current is highest when
VIN is approximately 2V.
5. Measured with port in high–impedance output mode.
6. Measured with port in Quasi–Bidirectional output mode.
7. Load capacitance for all outputs=80pF.
8. Under steady state (non–transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin:
15mA (*NOTE: This is 85
°
C specification for VDD = 5V.)
Maximum IOL per 8–bit port:
26mA
Maximum total IOL for all outputs:
71mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
9. See Figures 29, 30, 32, and 33 for IDD test conditions, and Figure 31 for ICC vs. Frequency.