- 您現在的位置：買賣IC網 > PDF目錄376449 > X96012V14I (INTERSIL CORP) Universal Sensor Conditioner with Dual Look Up Table Memory and DACs PDF資料下載
參數資料
| 型號： | X96012V14I |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Universal Sensor Conditioner with Dual Look Up Table Memory and DACs |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| 封裝： | PLASTIC, MO-153AC, TSSOP-14 |
| 文件頁數： | 20/27頁 |
| 文件大?。?/td> | 383K |
| 代理商： | X96012V14I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
20
FN8216.0
March 10, 2005
Serial Clock and Data
Data states on the SDA line can change only while
SCL is LOW. SDA state changes while SCL is HIGH
are reserved for indicating START and STOP condi-
tions. See Figure 13. On power-up of the X96012, the
SDA pin is in the input mode.
Serial Start Condition
All commands are preceded by the START condition,
which is a HIGH to LOW transition of SDA while SCL
is HIGH. The device continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition has been
met. See Figure 12.
Serial Stop Condition
All communications must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH. The STOP condition is also used
to place the device into the Standby power mode after
a read sequence. A STOP condition can only be
issued after the transmitting device has released the
bus. See Figure 12.
Serial Acknowledge
An ACK (Acknowledge), is a software convention used
to indicate a successful data transfer. The transmitting
device, either master or slave, releases the bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data. See Figure 14.
The device responds with an ACK after recognition of
a START condition followed by a valid Slave Address
byte. A valid Slave Address byte must contain the
Device Type Identifier 1010, and the Device Address
bits matching the logic state of pins A2, A1, and A0.
See Figure 16.
If a write operation is selected, the device responds
with an ACK after the receipt of each subsequent
eight-bit word.
In the read mode, the device transmits eight bits of
data, releases the SDA line, and then monitors the line
for an ACK. The device continues transmitting data if
an ACK is detected. The device terminates further
data transmissions if an ACK is not detected. The
master must then issue a STOP condition to place the
device into a known state.
The X96012 acknowledges all incoming data and
address bytes except: 1) The “Slave Address Byte”
when the “Device Identifier” or “Device Address” are
wrong; 2) All “Data Bytes” when the “WEL” bit is “0”,
with the exception of a “Data Byte” addresses to loca-
tion 86h; 3) “Data Bytes” following a “Data Byte”
addressed to locations 80h, 85h, or 86h.
Figure 11. D/A Converter Power-on Reset Response
I
x
I
x
x 10%
ADC TIME
Current
Time
Time
Vcc
V
ADCOK
0V
Voltage
X96012
相關PDF資料 |
PDF描述 |
|---|---|
| X96012 | Universal Sensor Conditioner with Dual Look-up Table Memory and DACs(通用傳感器調節器，帶雙查找表存儲器及DACs) |
| X98014L128-3.3-Z | 140MHz Triple Video Digitizer with Digital PLL |
| X98014L128-3.3 | 140MHz Triple Video Digitizer with Digital PLL |
| X98014 | 140MHz Triple Video Digitizer with Digital DLL(帶有數字PLL的140MHz三路視頻信號數字轉換器) |
| X98017 | 170MHz Triple Video Digitizer with Digital PLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X96012V14IZ | 功能描述:板上安裝溫度傳感器 UNIVERSAL SENSOR CONDITIO W/DL LOOKUP RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| X96012V14IZT1 | 功能描述:板上安裝溫度傳感器 UNIVERSAL SENSOR CONDITIO W/DL LOOKUP RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| X9601XEVAL | 制造商:Intersil Corporation 功能描述:X9601 EVALUATION BOARD - Bulk |
| X9650M | 制造商:EPCOS 制造商全稱:EPCOS 功能描述:Bandpass Filter |
| X-97-488 | 制造商:Brady Corporation 功能描述:Labels External Width:0.9" 制造商:Brady Corporation 功能描述:LABEL IDENTIFICATION 22.86X22.86 BLK/WHT; Background Color:White; Color:Black on White; External Width:0.9"; For Use With:IDXPERT Hand-Held Labeler; Label Material:Polyester; Label Size:22.86 x 22.86mm; Label Type:Identification ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。