- 您現在的位置：買賣IC網 > PDF目錄203632 > W78M64110SBC (WHITE ELECTRONIC DESIGNS CORP) 8M X 64 FLASH 3.3V PROM, 110 ns, PBGA159 PDF資料下載
參數資料
| 型號： | W78M64110SBC |
| 廠商： | WHITE ELECTRONIC DESIGNS CORP |
| 元件分類： | PROM |
| 英文描述： | 8M X 64 FLASH 3.3V PROM, 110 ns, PBGA159 |
| 封裝： | 13 X 22 MM, 1.27 MM PITCH, PLASTIC, BGA-159 |
| 文件頁數： | 5/50頁 |
| 文件大?。?/td> | 1679K |
| 代理商： | W78M64110SBC |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
13
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
W78M64VP-XSBX
November 2009
2010 White Electronic Designs Corp. All rights reserved
Rev. 10
White Electronic Designs Corp. reserves the right to change products or specications without notice.
change the status of the persistently locked sectors,
a few more steps are required. First, the PPB Lock Bit
must be cleared by either putting the device through a
power-cycle, or hardware reset. The PPBs can then be
changed to reect the desired settings. Setting the PPB
Lock Bit once again locks the PPBs, and the device
operates normally again.
6. To achieve the best protection, it is recommended to
execute the PPB Lock Bit Set command early in the
boot code and protect the boot code by holding WP#/
ACC = VIL. Note that the PPB and DYB bits have the
same function when WP#/ACC = VHH as they do when
ACC =VIH.
PERSISTENT PROTECTION BIT LOCK
BIT
The Persistent Protection Bit Lock Bit is a global volatile
bit for all sectors. When set (programmed to “0”), it locks
all PPBs and when cleared (programmed to “1”), allows
the PPBs to be changed. There is only one PPB Lock Bit
per device.
NOTES
1. No software command sequence unlocks this bit unless
the device is in the password protection mode; only a
hardware reset or a power-up clears this bit.
2. The PPB Lock Bit must be set (programmed to “0”)
only after all PPBs are conFIG:d to the desired settings.
PASSWORD PROTECTION METHOD
The Password Protection Method allows an even higher
level of security than the Persistent Sector Protection Mode
by requiring a 64-bit password for unlocking the device PPB
Lock Bit. In addition to this password requirement, after
power up and reset, the PPB Lock Bit is set “0” to maintain
the password mode of operation. Successful execution
of the Password Unlock command by entering the entire
password clears the PPB Lock Bit, allowing for sector PPBs
modications.
NOTES
1. There is no special addressing order required for
programming the password. Once the Password is
written and veried, the Password Mode Locking Bit
must be set in order to prevent access.
2. The Password Program Command is only capable of
programming “0”s. Programming a “1” after a cell is
programmed as a “0” results in a time-out with the cell
as a “0”.
3. The password is all “1”s when shipped from the factory.
4. All 64-bit password combinations are valid as a
password.
5. There is no means to verify what the password is after
it is set.
6. The Password Mode Lock Bit, once set, prevents
reading the 64-bit password on the data bus and further
password programming.
7. The Password Mode Lock Bit is not erasable.
8. The lower two address bits (A1–A0) are valid during the
Password Read, Password Program, and Password
Unlock.
9. The exact password must be entered in order for the
unlocking function to occur.
10. The Password Unlock command cannot be issued
any faster than 1 μs at a time to prevent a hacker from
running through all the 64-bit combinations in an attempt
to correctly match a password.
11. Approximately 1 μs is required for unlocking the device
after the valid 64-bit password is given to the device.
12. Password verification is only allowed during the
password programming operation.
13. All further commands to the password region are
disabled and all operations are ignored.
14. If the password is lost after setting the Password Mode
Lock Bit, there is no way to clear the PPB Lock Bit.
15. Entry command sequence must be issued prior to any
of any operation and it disables reads and writes for
Sector 0. Reads and writes for other sectors excluding
Sector 0 are allowed.
16. If the user attempts to program or erase a protected
sector, the device ignores the command and returns
to read mode.
17. A program or erase command to a protected sector
enables status polling and returns to read mode without
having modied the contents of the protected sector.
18. The programming of the DYB, PPB, and PPB Lock for a
given sector can be veried by writing individual status
read commands DYB Status, PPB Status, and PPB
Lock Status to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| W78M64V100SBC | 8M X 64 FLASH 3.3V PROM MODULE, 100 ns, PBGA159 |
| W78M64VP120SBM | SPECIALTY MEMORY CIRCUIT, PBGA156 |
| W78M64VP120SBI | SPECIALTY MEMORY CIRCUIT, PBGA156 |
| W83L761G | DIGITAL TEMP SENSOR-SERIAL |
| W8D-PF29062 | 36 CONTACT(S), FEMALE, STRAIGHT SINGLE PART CARD EDGE CONN, PRESS FIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78M64VP110SBM | 制造商:Microsemi Corporation 功能描述:8MX64 FLASH 3.3V PAGE MODE - Bulk |
| W78M64V-XSBX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flash MCP |
| W78NCSX-23 | 功能描述:低信號繼電器 - PCB 4PDT 3A 24VDC IND RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| W78PCX-1 | 制造商:Magnecraft 功能描述: |
| W78PCX-2 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。