- 您現在的位置：買賣IC網 > PDF目錄68459 > W6692ACF (WINBOND ELECTRONICS CORP) DATACOM, ISDN CONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | W6692ACF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | DATACOM, ISDN CONTROLLER, PQFP100 |
| 封裝： | QFP-100 |
| 文件頁數： | 26/98頁 |
| 文件大?。?/td> | 584K |
| 代理商： | W6692ACF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
Data Sheet
W6692A PCI ISDN S/T-Controller
Publication Release Date:
Mar,2000
Revision 1.0
-32 -
-
Digital loop via DLP bit in D_MODE register: In the layer 2 block, the transmitted 2B+D data are internally
looped (from HDLC transmitter to HDLC receiver), and in the PCM ports, the transmitted B channels are
internally looped (from PCM inputs to PCM outputs). The clock timings are generated internally and are
independent of the S bus timing. This loop function is used for test of PCM and higher layer functions, excluding
layer 1. After hardware reset, W6692A will power down if S bus is not connected or if there is no signal on the S
bus. In this case, the C/I command ECK must be issued to power up the chip.
-
Analog loop via the C/I command EAL: The analog S interface transmitter is internally connected to the S
interface receiver. When the receiver has synchronized itself to the internal INFO 3 signal, the message "Test
Indication" or "Awake Test Indication" is delivered to the CIR register. No signal is transmitted over the S
interface.
In this mode, the S interface awake detector is enabled. Therefore if a level (INFO 2/ INFO 4) is detected on the S
interface, this will be reported by the "Awake Test Indication (ATI)" indication.
-
Remote loopback via RLP bit in D_MODE register: The digital 2B data received from the S interface receiver is
loopbacked to the S interface transmitter. The D channel is not looped. When RLP is enabled, layer 1 D channel is
connected to HDLC port and DLP cannot be enabled.
-
Transmission of special test signals via layer 1 command:
* Send Single Pulses (SSP): To send isolated single pulses of alternating polarity, with pulse width of one bit
time, 250 us apart, with a repetition frequency of 2 kHz.
* Send Continuous Pulses (SCP): To send continuous pulses of alternating polarity, with pulse width of bit
time. The repetition frequency is 96 kHz.
FIG.7.7 SSP AND SCP TEST SIGNALS
250 us
(a) Single pulses
(b) Continuous pulses
相關PDF資料 |
PDF描述 |
|---|---|
| W6694ACD | DATACOM, ISDN CONTROLLER, PQFP48 |
| W671320P | TELECOM-SLIC, PQCC28 |
| W671361P | TELECOM-SLIC, PQCC28 |
| W671361Y | TELECOM-SLIC, QCC32 |
| W671310P | TELECOM-SLIC, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W6694 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:USB Bus ISDN S/T-Controller |
| W6694A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with USB 1.1 Interface |
| W6694CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:USB Bus ISDN S/T-Controller |
| W66ARX-18 | 制造商:Magnecraft 功能描述: |
| W66MAF185X | 制造商:Panasonic Industrial Company 功能描述:CRT |
發布緊急采購，3分鐘左右您將得到回復。