- 您現在的位置：買賣IC網 > PDF目錄68459 > W6692ACF (WINBOND ELECTRONICS CORP) DATACOM, ISDN CONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | W6692ACF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | DATACOM, ISDN CONTROLLER, PQFP100 |
| 封裝： | QFP-100 |
| 文件頁數： | 15/98頁 |
| 文件大?。?/td> | 584K |
| 代理商： | W6692ACF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
Data Sheet
W6692A PCI ISDN S/T-Controller
Publication Release Date:
Mar,2000
Revision 1.0
-22 -
After hardware reset, the receiver may enter power down state in order to save power consumption. In this state, the internal
clocks are turned off, but the analog level detector is still active to detect signal coming from the S interface. The power down
state is left either by non-INFO 0 signal from S interface or C/I command from microprocessor.
7.2.2 Receiver Clock Recovery And Timing Generation
A Digital Phase Locked Loop (DPLL) circuit is used to derive the receive clock from the received data stream. This DPLL
uses a 7.68 MHz clock as reference. According to I.430, the transmit clock is normally delayed by 2 bit time from the receive
clock. The "total phase deviation from input to output" is -7% to +15% of a bit period. In some cases, delay compensation may be
needed to meet this requirement (see OPS1-0 bits in D_CTL register).
TABLE 7.1 OUTPUT PHASE DELAY COMPENSATION TABLE
OPS1
OPS0
Effect
0
No phase delay compensation
0
1
Phase delay compensation 260 ns
1
0
Phase delay compensation 520 ns
1
Phase delay compensation 1040 ns
W6692A does not need RC filter on receiver side, therefore zero delay compensation is selected normally. This is also the
default setting.
The PCM output clocks (PFCK1-2, PBCK) are locked to the S-interface timing with jitter. See the electrical specification.
7.2.3 Layer 1 Activation/Deactivation
The layer 1 activation/deactivation procedures are implemented by a finite state machine according to TE mode. The state
transitions are triggered by signals received at S interface or commands issued from microprocessor. The state outputs signals to
S interface and indication to microprocessor. The CIX register is used by microprocessor to issue command, and the CIR register
is used by microprocessor to receive indication.
Some commands are used for special purposes. They are "layer 1 reset", "analog loopback", "send continuous zeros" and
"send single zero".
7.2.3.1 States Descriptions And Command/Indication Codes
F3
Deactivated
without clock
This is the "deactivated" state of ITU-T I.430. The receive line awake unit is active except during a hardware reset pulse.
After reset, once the indication "1111" has been read out, internal clocks will turn off and stay at this state if INFO 0 is received
on the S line. The turn off time is approximate 93 ms. The ECK command must be issued to activate the clocks.
F3
Deactivated
with clock
相關PDF資料 |
PDF描述 |
|---|---|
| W6694ACD | DATACOM, ISDN CONTROLLER, PQFP48 |
| W671320P | TELECOM-SLIC, PQCC28 |
| W671361P | TELECOM-SLIC, PQCC28 |
| W671361Y | TELECOM-SLIC, QCC32 |
| W671310P | TELECOM-SLIC, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W6694 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:USB Bus ISDN S/T-Controller |
| W6694A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with USB 1.1 Interface |
| W6694CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:USB Bus ISDN S/T-Controller |
| W66ARX-18 | 制造商:Magnecraft 功能描述: |
| W66MAF185X | 制造商:Panasonic Industrial Company 功能描述:CRT |
發布緊急采購，3分鐘左右您將得到回復。