- 您現在的位置：買賣IC網 > PDF目錄68449 > W28J321BB90L (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 2.7V PROM, 90 ns, PBGA48 PDF資料下載
參數資料
| 型號： | W28J321BB90L |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 2.7V PROM, 90 ns, PBGA48 |
| 封裝： | 8 X 11 MM, 0.75 MM PITCH, TFBGA-48 |
| 文件頁數： | 34/47頁 |
| 文件大小： | 1385K |
| 代理商： | W28J321BB90L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
W28J321B/T
- 4 -
3. PRODUCT OVERVIEW
The W28J321B/T is a high-performance 32M-bit Boot Block Flash memory organized as 2M-word of
16 bits. The 2M-word of data is arranged in two 4k-word boot blocks, six 4k-word parameter blocks
and sixty-three 32k-word main blocks which are individually erasable, lockable and unlockable in-
system. The memory map is shown in Figure 3.
The dedicated VPP pin gives complete data protection when VPP ≤ V.
A Command User Interface (CUI) serves as the interface between the system processor and internal
operation of the device. A valid command sequence written to the CUI initiates device automation. An
internal Write State Machine (WSM) automatically executes the algorithms and timings necessary for
block erase, full chip erase, word write and lock-bit configuration operations.
A block erase operation erases one of the device's 32Kword blocks typically within 1.2s (3V VDD, 3V
VPP), 4k-word blocks typically within 0.6s (3V VDD, 3V VPP) independent of other blocks. Each block
can be independently erased minimum 100,000 times. Block erase suspend mode allows system
software to suspend block erase to read or write data from any other block.
Writing memory data is performed in word increments of the device’s 32k-word blocks typically within
33s (3V VDD, 3V VPP), 4k-word blocks typically within 36 S (3V VDD, 3V VPP). Word write suspend
mode enables the system to read data or execute code from any other flash memory array location.
Individual block locking uses a combination of bits, seventy-one block lock-bits, a permanent lock-bit
and #WP pin, to lock and unlock blocks. Block lock-bits gate block erase, full chip erase and word
write operations, while the permanent lock-bit gates block lock-bit modification and locked block
alternation. Lock-bit configuration operations (Set Block Lock-Bit, Set Permanent Lock-Bit and Clear
Block Lock-Bits commands) set and cleared lock-bits.
The status register indicates when the WSM’s block erase, full chip erase, word write or lock-bit
configuration operation is finished.
The access time is 90 nS (tAVQV) over the operating temperature range (-40° C to +85° C) and VDD
supply voltage range of 2.7V to 3.6V.
The Automatic Power Savings (APS) feature substantially reduces active current when the device is in
static mode (addresses not switching). In APS mode, the typical ICCR current is 4 A (CMOS) at 3.0V
VDD.
When #CE and #RESET pins are at VDD, the ICC CMOS standby mode is enabled. When the #RESET
pin is at Vss, reset mode is enabled which minimizes power consumption and provides write
protection. A reset time (tPHQV) is required from #RESET switching high until outputs are valid.
Likewise, the device has a wake time (tPHEL) from #RESET-high until writes to the CUI are recognized.
With #RESET at VSS, the WSM is reset and the status register is cleared.
Overwriting a "0" to a bit already holding a data "0" may render this bit un-erasable. In order to avoid
this potential "stuck bit" failure, when re-programming (changing data from "1" to "0") the following
should be followed:
Program "0" for the bit in which you want to change data from "1" to "0".
Program "1" for the bit which is already holding a data "0". (Note: Since only an erase process
can change the data from "0" to "1", programming "1" to a bit holding a data “0” will not
change the data).
For example, changing data from "10111101" to "10111100" requires "11111110" programming.
相關PDF資料 |
PDF描述 |
|---|---|
| W29C010MP90B | 128K X 8 FLASH 5V PROM, 90 ns, PQCC32 |
| W29C010MP90 | 128K X 8 FLASH 5V PROM, 90 ns, PQCC32 |
| W29C011AP15N | 128K X 8 FLASH 5V PROM, 150 ns, PQCC32 |
| W29C020CP-12 | 256K X 8 FLASH 5V PROM, 120 ns, PQCC32 |
| W29C022T-12 | 256K X 8 FLASH 5V PROM, 120 ns, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W28NK60Z | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:N-CHANNEL 600 V - 0.155з - 27A TO-247 Zener-Protected SuperMESH MOSFET |
| W28-SQ11A-10 | 功能描述:CIRCUIT BREAK 10A W/SWITCH RoHS:否 類別:過電壓，電流，溫度裝置 >> 斷路器 系列:W28 標準包裝:3 系列:AS168X 斷路器類型:熱磁動式 電壓:65VDC，277/480VAC 電流 - 跳閘(It):30A 極數:3 觸動器類型:按片 安裝類型:DIN 軌道 其它名稱:4420.02104420.0210-ND486-2338AS168X-CB3G300-NDCBE AS168X-CB3G300 |
| W28-SQ11A-15 | 制造商:TE Connectivity 功能描述: |
| W28-SQ11A-3 | 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 3A 250VAC/32VDC |
| W28-SQ11A-5 | 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 5A 250VAC/32VDC |
發布緊急采購，3分鐘左右您將得到回復。