參數資料
型號： UPSD3233BV-40U1T
廠商： 意法半導體
英文描述： Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
中文描述： 閃存可編程系統設備與8032微控制器核心和64Kbit SRAM的
文件頁數： 111/176頁
文件大小： 1081K
代理商： UPSD3233BV-40U1T
111/176
μ
PSD323X
Toggle Flag (DQ6).
The Flash memory offers an-
other way for determining when theProgram cycle
is completed.During the internal WRITE operation
and when either the FS0-FS7 or CSBOOT0-
CSBOOT3 is true, the Toggle Flag Bit (DQ6) tog-
gles from ’0’ to ’1’ and ’1’ to ’0’ on subsequent at-
tempts to read any byte of the memory.
When the internal cycle is complete, the toggling
stops and the data READ on the Data Bus D0-D7
is the addressed memory byte. The device is now
accessible for a new READ or WRITE operation.
The cycle is finished when two successive Reads
yield the same output data.
I
The Toggle Flag Bit (DQ6) is effective after the
fourth WRITE pulse (for a Program instruction)
or after the sixth WRITE pulse (for an Erase
instruction).
I
If the byte to be programmed belongs to a
protected Flash memory sector, the instruction
is ignored.
I
If all the Flash memory sectors selected for
erasure are protected, the Toggle Flag Bit
(DQ6) toggles to ’0’for about 100
μ
s and then
returns to the previous addressed byte.
Error Flag (DQ5).
During a normal Program or
Erase cycle, the Error Flag Bit (DQ5) is to ’0.’This
bit is set to ’1’ when there is a failure during Flash
memory Byte Program, Sector Erase, or Bulk
Erase cycle.
In thecase of Flash memory programming, theEr-
ror FlagBit (DQ5)indicates theattempt to program
a Flash memory bit from the programmed state,
’0’, to the erased state, ’1,’ which is not valid. The
Error Flag Bit (DQ5) may also indicate a Time-out
condition while attempting to program a byte.
In caseof an error ina Flashmemory Sector Erase
or ByteProgram cycle, the Flash memory sector in
which the error occurred or to which the pro-
grammed byte belongs must no longer be used.
Other Flash memory sectors may still be used.
The Error Flag Bit (DQ5) is reset after a Reset
Flash instruction.
Erase Time-out Flag (DQ3).
The Erase
out Flag Bit (DQ3) reflects the time-out period al-
lowed between two consecutive Sector Erase in-
structions. The Erase Time-out Flag Bit (DQ3) is
reset to ’0’after a Sector Erasecycle for a time pe-
riod of 100
μ
s + 20% unless an additional Sector
Erase instruction is decoded. After this time peri-
od, or when the additional Sector Erase instruction
is decoded, the Erase Time-out Flag Bit (DQ3) is
set to ’1.’
Time-
Table 86. Status Bit
Note: 1. X = Not guaranteed value, can be read either ’1’or ’0.’
2. DQ7-DQ0 represent the Data Bus bits, D7-D0.
3. FS0-FS7 and CSBOOT0-CSBOOT3 are active High.
Functional Block
FS0-FS7/CSBOOT0-
CSBOOT3
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
Flash Memory
V
IH
Data
Polling
Toggle
Flag
Error
Flag
X
Erase
Time-
out
X
X
X
相關PDF資料
PDF描述
uPSD3233 Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可編程系統器)
uPSD3234(中文) Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可編程系統器)
uPSD3212C(中文) Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM(帶8032微控制器內核和16Kbit SRAM的FLASH可編程系統器件)
uPSD3254A(中文) Flash Programmable System Devices with 8032 Microcontroller Core(帶8032微控制器內核的FLASH可編程系統器件)
uPSD3254BV(中文) Flash Programmable System Devices with 8032 Microcontroller Core(帶8032微控制器內核的FLASH可編程系統器件)
相關代理商/技術參數
參數描述
UPSD3233BV-40U6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
UPSD3233BV-40U6T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core
UPSD32348V24V6ES 制造商:ST MICRO 功能描述:*
UPSD3234A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core
UPSD3234A-24T1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*