參數資料
型號： UPD68AMC-XXX-5A4
元件分類： 微控制器/微處理器
英文描述： 4-BIT, OTPROM, 4.5 MHz, MICROCONTROLLER, PDSO20
封裝： 0.300 INCH, PLASTIC, SSOP-20
文件頁數： 69/73頁
文件大?。?/td> 561K
代理商： UPD68AMC-XXX-5A4
69
PD67, 67A, 68, 68A, 69
Data Sheet U14935EJ2V1DS
1
2
3
4
VOLTAGE APPLICATION WAVEFORM AT INPUT PIN
Waveform distortion due to input noise or a reflected wave may cause malfunction. If the input of the
CMOS device stays in the area between VIL (MAX) and VIH (MIN) due to noise, etc., the device may
malfunction. Take care to prevent chattering noise from entering the device when the input level is
fixed, and also in the transition period when the input level passes through the area between VIL (MAX)
and VIH (MIN).
HANDLING OF UNUSED INPUT PINS
Unconnected CMOS device inputs can be cause of malfunction. If an input pin is unconnected, it is
possible that an internal input level may be generated due to noise, etc., causing malfunction. CMOS
devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using pull-up or pull-down circuitry. Each unused pin should be connected to VDD or
GND via a resistor if there is a possibility that it will be an output pin. All handling related to unused pins
must be judged separately for each device and according to related specifications governing the device.
PRECAUTION AGAINST ESD
A strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as
much as possible, and quickly dissipate it when it has occurred.
Environmental control must be
adequate. When it is dry, a humidifier should be used. It is recommended to avoid using insulators that
easily build up static electricity. Semiconductor devices must be stored and transported in an anti-static
container, static shielding bag or conductive material. All test and measurement tools including work
benches and floors should be grounded.
The operator should be grounded using a wrist strap.
Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for
PW boards with mounted semiconductor devices.
STATUS BEFORE INITIALIZATION
Power-on does not necessarily define the initial status of a MOS device. Immediately after the power
source is turned ON, devices with reset functions have not yet been initialized. Hence, power-on does
not guarantee output pin levels, I/O settings or contents of registers. A device is not initialized until the
reset signal is received. A reset operation must be executed immediately after power-on for devices
with reset functions.
POWER ON/OFF SEQUENCE
In the case of a device that uses different power supplies for the internal operation and external
interface, as a rule, switch on the external power supply after switching on the internal power supply.
When switching the power supply off, as a rule, switch off the external power supply and then the
internal power supply. Use of the reverse power on/off sequences may result in the application of an
overvoltage to the internal elements of the device, causing malfunction and degradation of internal
elements due to the passage of an abnormal current.
The correct power on/off sequence must be judged separately for each device and according to related
specifications governing the device.
INPUT OF SIGNAL DURING POWER OFF STATE
Do not input signals or an I/O pull-up power supply while the device is not powered. The current
injection that results from input of such a signal or I/O pull-up power supply may cause malfunction and
the abnormal current that passes in the device at this time may cause degradation of internal elements.
Input of signals during the power off state must be judged separately for each device and according to
related specifications governing the device.
NOTES FOR CMOS DEVICES
5
6
相關PDF資料
PDF描述
UPD703032AYGF-XXX-3BA 32-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
UPD70F3079YGF-3BA 32-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP100
UPD750004GBA-XXX-3BS-MTX 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP44
UPD754244GS-XXX-GJG 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
UPD75P3018AGK-9EU Circular Connector; No. of Contacts:56; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:25-4 RoHS Compliant: No
相關代理商/技術參數
參數描述
UPD68MC-XXX-5A4 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|4-BIT|CMOS|SSOP|20PIN|PLASTIC
UPD69 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontrollers for Remote Controllers Pamphlet | Pamphlet[11/2002]
UPD6900C 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Digital-to-Analog Converter
UPD6900G 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Digital-to-Analog Converter
UPD6901C 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC without Color Palette
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*