- 您現在的位置：買賣IC網 > PDF目錄373745 > TSS463C (Atmel Corp.) VAN Data Link Controller with Serial Interface PDF資料下載
參數資料
| 型號： | TSS463C |
| 廠商： | Atmel Corp. |
| 英文描述： | VAN Data Link Controller with Serial Interface |
| 中文描述： | 凡數據與串行接口鏈路控制器 |
| 文件頁數： | 51/59頁 |
| 文件大?。?/td> | 492K |
| 代理商： | TSS463C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
51
TSS463C
7601B–AUTO–02/06
Activate, Idle and
Sleep Modes
Sleep, idle and activate commands are located in the Command Register (0x03). These
three commands are general commands for the TSS463C.
Idle and Activate
Commands
After reset, the TSS463C starts in idle mode. In this mode, the oscillator operates
(CKOUT pin active) but the circuit cannot transmit or receive anything on the VAN bus.
The TxD output (pin 12) is in tri-state mode, a pull-up resistor must be provided exter-
nally or by the line driver to avoid floating state on the VAN bus. To activate the
TSS463C, the user must set the activate bit (ACTI) and reset the idle bit (IDLE).
Figure 35.
Idle and Activate Timings
In both cases, the idle state can be verified reading the Line Status register (0x04).
Sleep Command
If the user sets the sleep bit (SLEEP), the TSS463C enters in sleep mode, regardless of
the values of activate and idle bits. It means that, all non-user registers are set-up to
reduce the power consumption and the internal oscillator is immediately stopped. Then,
accesses to all registers (and to the messages) via the SPI/SCI interface are impossible
and CKOUT is not provided.
To exit from this mode the user must apply either an hardware reset (external reset pin)
either an asynchronous software reset (via the SPI/SCI interface).
In a typical application (see Figure 5), using the CKOUT feature (pin 8), if the TSS463C
is put in sleep mode, the clock provided to the microcontroller is stopped. So, the system
does not run and the only way to awake this application is an external reset.
(max)
RxD
TxD
After Reset
Idle Mode
Activate Mode
Activate command
3 TS
8 TS
12 TS
TS: Timeslot Period
SOF
SOF
Idle Command
FCS
E
A
5 TS
4 TS
RxD
INT
Idle Mode
Activate Mode
相關PDF資料 |
PDF描述 |
|---|---|
| TSS4B02G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS4B03G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS4B01G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS5G45S | TOSHIBA SOLID STATE AC RELAY |
| TSS5J45S | TOSHIBA SOLID STATE AC RELAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSS463C-TERA-9 | 功能描述:網絡控制器與處理器 IC ASICS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TSS463C-TERZ-9 | 制造商:Atmel Corporation 功能描述: |
| TSS463C-TESZ-9 | 功能描述:網絡控制器與處理器 IC ASICS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TSS463D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| TSS463R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
發布緊急采購，3分鐘左右您將得到回復。