- 您現在的位置：買賣IC網 > PDF目錄373745 > TSS461F (Atmel Corp.) VAN Data Link Controller PDF資料下載
參數資料
| 型號： | TSS461F |
| 廠商： | Atmel Corp. |
| 英文描述： | VAN Data Link Controller |
| 中文描述： | 凡數據鏈路控制器 |
| 文件頁數： | 21/57頁 |
| 文件大?。?/td> | 397K |
| 代理商： | TSS461F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
21
7615A–AUTO–02/06
TSS461F
filters) with the data transmitted on TxD output.
At a time when the transmission logic generates a dominant (recessive transition), the inputs
can give different values. Taking into account the filtering delay, the bus line seen as
dominant is assumed to be correct, the other one, recessive, is considered faulty. The
diagnosis mode is changed to reflect that.
Protocol fault:
The protocol fault is detected by counting the number of consecutive dominant timeslots.
If eight consecutive timeslots are dominant, the diagnosis mode will change to the major
error mode.
Generation of
Internal Signals
RI Signal (Return to
Idle)
This signal is used to return to nominal mode in the three specified selection modes (see
section “Diagnosis States” and section “Programming Modes”). The RI signal is disabled in auto-
matic selection mode.
The RI signal is a pulse generated when an EOF is detected. So, at the end of each frame, the
user, regarding the diagnosis status bit Sa, Sb & Sc, can select its own choice.
SDC Signal
(Synchronous
Diagnosis Clock)
This time base is used by diagnosis system in automatic selection mode (see
section “Programming Modes”) when no event is recorded on the bus.
The SDC is generated either by a special SDC divider connected to the timeslot clock, or manu-
ally. The SDC clock period must be longer compared to the timeslot duration.
A typical SDC period should be greater than the maximum frame length appearing on the VAN
network.
TIP Signal
(Transmission In
Progress)
This signal must be enabled to allow the transmission diagnosis (see section “Transition
Analyses”).
The TIP turns on synchronously at the beginning of the transmission:
For asynchronous bus access, the beginning of SOF,
For synchronous bus access, the beginning of the identifier field,
For a request of in frame reply, the RTR bit of the command field.
The TIP turns off synchronously at the end of the transmission:
after EOF
after a losing of arbitration or a code violation detection
for a requester of in frame reply, when the arbitration is lost on RTR the bit.
This signal is not generated when the transmission logic only sends an ACK.
相關PDF資料 |
PDF描述 |
|---|---|
| TSS463-AAR | VAN Data Link Controller with Serial Interface |
| TSS463A-TERZ | VAN Data Link Controller with Serial Interface |
| TSS463C | VAN Data Link Controller with Serial Interface |
| TSS4B02G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS4B03G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSS461F-TDRZ-9 | 功能描述:網絡控制器與處理器 IC Van Data Link Controller RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TSS461F-TDSZ-9 | 功能描述:網絡控制器與處理器 IC ASICS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TSS463 | 制造商:Atmel Corporation 功能描述:LAN Node Controller, 16 Pin, SOP 制造商:Temic 功能描述:LAN Node Controller, 16 Pin, SOP |
| TSS463-AA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TSS463-AA [Updated 3/03. 60 Pages] |
發布緊急采購，3分鐘左右您將得到回復。