參數資料
型號: TMS320WP010PZA
英文描述: Cell-Phone Circuit
中文描述: 手機電路
文件頁數: 20/132頁
文件大小: 1707K
代理商: TMS320WP010PZA
SPRS145G
JULY 2000
REVISED FEBRUARY 2002
20
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
1443
pin functions (continued)
Table 2. LF240xA and LC240xA Pin List and Package Options
(Continued)
PIN NAME
LF2407A
(144-PGE)
2406A
(100-PZ)
LC2404A
(100-PZ)
2403A,
LC2402A
(64-PAG)
and
2402A
(64-PG)
DESCRIPTION
EMULATION AND TEST (CONTINUED)
TRST
1
1
1
33
JTAG test reset with internal pulldown. TRST, when
driven high, gives the scan system control of the
operations of the device. If this signal is not
connected or driven low, the device operates in its
functional mode, and the test reset signals are
ignored.
(
)
NOTE: Do not use pullup resistors on TRST; it has
an internal pulldown device. In a low-noise
environment, TRST can be left floating. In a
high-noise environment, an additional pulldown
resistor may be needed. The value of this resistor
should be based on drive strength of the debugger
pods applicable to the design. A 2.2-k
resistor
generally offers adequate protection. Since this is
application-specific, it is recommended that each
target board is validated for proper operation of the
debugger and the application.
ADDRESS, DATA, AND MEMORY CONTROL SIGNALS
DS
87
Data space strobe. IS, DS, and PS are always high
unless low-level asserted for access to the relevant
external memory space or I/O. They are placed in
the high-impedance state.
IS
82
I/O space strobe. IS, DS, and PS are always high
unless low-level asserted for access to the relevant
external memory space or I/O. They are placed in
the high-impedance state.
PS
84
Program space strobe. IS, DS, and PS are always
high unless low-level asserted for access to the
relevant external memory space or I/O. They are
placed in the high-impedance state.
R/W
92
Read/write qualifier signal. R/W indicates transfer
direction during communication to an external
device. It is normally in read mode (high), unless low
level is asserted for performing a write operation.
R/W is placed in the high-impedance state.
Bold, italicized pin names
indicate pin function after reset.
GPIO
General-purpose input/output pin. All GPIOs come up as input after reset.
§
It is highly recommended that VCCA be isolated from the digital supply voltage (and VSSA from digital ground) to maintain the specified accuracy
and improve the noise immunity of the ADC.
Only when all of the following conditions are met: EMU1/OFF is low, TRST is low, and EMU0 is high
#No power supply pin (VDD, VDDO, VSS, or VSSO) should be left unconnected. All power supply pins must be connected appropriately for proper
device operation.
LEGEND:
Internal pullup
Internal pulldown
(Typical active pullup/pulldown value is
±
16
μ
A.)
相關PDF資料
PDF描述
TMX320LF2407APGES INSUL WASHER 10 PR
TMP320LC2404APZA Transient Voltage Suppressor Diodes
TMP320LC2404APZS Transient Voltage Suppressor Diodes
TMP320LC2406APZA Transient Voltage Suppressor Diodes
TMP320LC2406APZS Transient Voltage Suppressor Diodes
相關代理商/技術參數
參數描述
TMS320-XDS100-V2 功能描述:仿真器/模擬器 USB JTAG DONGLE XDS100V2 TMS320 RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
TMS320-XDS100-V3 功能描述:仿真器/模擬器 XDS100V3 DSP / ARM HIGH SPEED USB JTAG RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
TMS32AV110PBM 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:
TMS32C31PQA40 制造商:Texas Instruments 功能描述:
TMS32C5402PGER10G4 功能描述:數字信號處理器和控制器 - DSP, DSC Tape & Reel Version 5402PGE100 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT