- 您現在的位置：買賣IC網 > PDF目錄382592 > TL16PC564BLVPZ (Texas Instruments, Inc.) Tools, Stencil; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes PDF資料下載
參數資料
| 型號： | TL16PC564BLVPZ |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Tools, Stencil; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes |
| 中文描述： | 的PCMCIA通用異步收發器 |
| 文件頁數： | 4/33頁 |
| 文件大?。?/td> | 488K |
| 代理商： | TL16PC564BLVPZ |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
TL16PC564B, TL16PC564BLV
PCMCIA UNIVERSAL ASYNCHRONOUS RECEIVER TRANSMITTER
SLLS225A – MARCH 1996 – REVISED FEBRUARY 1998
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
INTER-
FACE
I/O
DESCRIPTION
NAME
ALE (AS)
NO.
26
S
I
Address-latch enable/address strobe. ALE(AS) is an address-latch enable in the Intel mode
and an address strobe in the Zilog mode. ALE (AS) is active high for an Intel subsystem and
active low for a Zilog subsystem.
Arbitration clock output. ARBCLKO is equal to the input on ARBCLKI divided by the
binary-coded divisor input on ARBPGM (1–0).
ARBCLKO
7
M
O
ARBCLKI
5
M
I
Arbitration clock input. ARBCLKI is the base clock used in arbitration for the attribute memory
DRAM and the reset validation circuitry.
ARBPGM0
ARBPGM1
8
9
M
I
Arbitration clock divisor program. These two bits set the divisor for ARBCLKI. Divide by 1, 2,
4, and 8 are available.
Baud output. BAUDOUT is an active-low 16
×
signal for the transmitter section of the UART.
The clock rate is established by the reference clock (UARTCLK) frequency divided by a divisor
specified by the baud generator divisor latches. BAUDOUT may also be used for the receiver
section by tying this output to the RCLK input.
Card enable 1 and card enable 2 are active-low signals. CE1 enables even-numbered
address bytes, and CE2 enables odd-numbered address bytes. A multiplexing scheme based
on HA0, CE1, and CE2 allows an 8-bit host to access all data on HD0 through HD7 if desired.
These signals have internal pullup resistors.
Chip select. CS is the active-low chip select from the Zilog or Intel microcontroller.
Clear to send. CTS is an active-low modem status signal whose condition can be checked by
reading bit 4 (CTS) of the modem status register (MSR). Bit 0 (delta clear to send) of the MSR
indicates that the signal has changed states since the last read from the MSR. If the
modem-status interrupt is enabled when CTS changes states, an interrupt is generated.
Data carrier detect. DCD is an active-low modem-status signal whose condition can be
checked by reading bit 7 (DCD) of the MSR. Bit 3 (delta data carrier detect) of the MSR
indicates that the signal has changed states since the last read from the MSR. If the
modem-status interrupt is enabled when DCD changes states, an interrupt is generated.
Data set ready. DSR is an active-low modem status signal whose condition can be checked
by reading bit 5 (DSR) of the MSR. Bit 1 (delta data set ready) of the MSR indicates that the
signal has changed states since the last read from the MSR. If the modem-status interrupt is
enabled when DSR changes states, an interrupt is generated.
Data terminal ready. DSD is an active-low signal. When active, DTR informs the modem or
data set that the UART is ready to establish communication. DTR is placed in the active state
by setting the DTR bit 0 of the modem control register (MCR) to a high level. DTR is placed
in the inactive state either as a result of a reset, doing a loop-mode operation, or resetting bit
0 (DTR) of the MCR.
BAUDOUT
38
U
O
CE1
CE2
94
62
H
I
CS
CTS
32
49
S
U
I
I
DCD
48
U
I
DSR
46
U
I
DTR
34
U
O
EXTEND
1
U
I
FIFO extend. When EXTEND is high, the UART is configured as a standard TL16C550 with
16-byte transmit and receive FIFOs. When EXTEND is low and FIFO control register (FCR)
bit 5 is high, the FIFOs are extended to 64 bytes and the receiver-interrupt trigger levels adjust
accordingly. EXTEND low in conjunction with FIFO control register (FCR) bit 4 set high
enables the auto-RTS function.
GND
4,6,13,16,30,
39,41,43,54,
66,68,69,80,91
M
Common ground
Host = H, Subsystem = S, UART = U, Miscellaneous = M
相關PDF資料 |
PDF描述 |
|---|---|
| TL16PC564BLV | PCMCIA UNIVERSAL ASYNCHRONOUS RECEIVER TRANSMITTER |
| TL172C | NORMALLY OFF SILICON HALL-EFFECT SWITCH |
| TL2218-285YPW | EXCALIBUR CURRENT-MODE SCSI TERMINATOR |
| TL2218 | EXCALIBUR CURRENT-MODE SCSI TERMINATOR |
| TL2218-285Y | EXCALIBUR CURRENT-MODE SCSI TERMINATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TL16PC564BPZ | 功能描述:UART 接口集成電路 Sngl UART w/64-Byte FIFOs PCMCIA Ifc RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| TL16PC564BPZG4 | 功能描述:UART 接口集成電路 Sgl UART w/64-Byte Fifos RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| TL16PIR552 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL UART WITH DUAL IrDA AND 1284 PARALLEL PORT |
| TL16PIR552PH | 功能描述:UART 接口集成電路 Dual UART w/Dl IrDA & 1284 Parallel Port RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| TL16PIR552PHG4 | 功能描述:UART 接口集成電路 DUAL UART W/DUAL IRDA & 1284 PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。