參數資料
型號: THMC50SSOPDBQ
廠商: Texas Instruments, Inc.
英文描述: KPT 55C 55#20 SKT RECP
中文描述: 遠程/本地溫度監視器和通風機的SMBus接口控制器
文件頁數: 11/32頁
文件大?。?/td> 437K
代理商: THMC50SSOPDBQ
THMC50
REMOTE/LOCAL TEMPERATURE MONITOR AND
FAN CONTROLLER WITH SMBus INTERFACE
SLIS090 – JULY 1999
11
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
Table 1. THMC50 ADD Terminal States and Resulting SMBus Slave Address
ADD TERMINAL
RESULTING THMC50 SMBUS ADDRESS
GND
0101110
No Connect
0101100
VCC
0101101
Refer to Figure 1 through Figure 5 for the SMBus timing diagrams. The THMC50 does not support the SMBSUS
or SMBALERT sideband signals referenced in the SMBus specification.
THMC50 usage
The following sections describe the typical usage for the THMC50.
power-on reset
Applying power to the VCC3AUX terminal causes a reset of all of the registers to their default states. Some
registers have indeterminate power-on values, such as the limit and RAM registers, and these are not shown
in the table. Writing limit values into the value RAM should be the first action performed after power up. Refer
to the register definition tables for default power-on values of all other registers.
If the FAN_SPD/NTEST_IN terminal is held high during power-on reset, the THMC50 enters the NAND tree test
mode. Once the NAND tree test mode is enabled, it can only be disabled by cycling VCC3AUX power.
The FAN_SPD analog output is reset to 0x00 whenever RST is asserted low. During the time RST is asserted
low, a THERM assertion will still cause the FAN_SPD analog output to go to full scale (0xFF).
The THMC50 contains a bidirectional reset terminal, AUXRST, which causes an internal reset when pulled low
externally. Refer to the section describing AUXRST for more detail.
soft reset
The THMC50 can be commanded to perform an internal soft reset by setting bit 4 of the configuration register
(0x40). This bit automatically clears itself after being set. A soft reset performs a similar reset to the power-on
reset, except that the value RAM remains unchanged. Registers that are reset by both types of reset include:
0
×
40 configuration register
0
×
41 interrupt status register
0
×
43 interrupt mask register
0
×
4C interrupt status register mirror
beginning a conversion
The THMC50 monitoring function is started by default. It is expected that the system BIOS initializes the
THMC50 as quickly as possible during POST. The BIOS should then clear the INT clear (bit 2) and set INT
enable (bit 1) in the configuration register (0
×
40) in order to enable THMC50 interrupts and the INT function.
The results of the sampling and conversion can be found in the value RAM and are available at any time.
相關PDF資料
PDF描述
THMR1E16-6 134,217,728-Word(256MBytes) by 18-Bit(128M-Word × 18Bit) Direct Rambus DRAM Module(I/O Frequency:600MHz)(256M字節(128M字× 18位)直接Rambus 動態RAM模塊(I/O 頻率:600MHz))
THMR1E16-7 134,217,728-Word(256MBytes) by 18-Bit(128M-Word × 18Bit) Direct Rambus DRAM Module(I/O Frequency:711MHz)(256M字節(128M字× 18位)直接Rambus 動態RAM模塊(I/O 頻率:711MHz))
THMR1E16-8 134,217,728-Word(256MBytes) by 18-Bit(128M-Word × 18Bit) Direct Rambus DRAM Module(I/O Frequency:800MHz)(256M字節(128M字× 18位)直接Rambus 動態RAM模塊(I/O 頻率:800MHz))
THMR1E4-6 33,554,432-Word(64MBytes) by 18-Bit(32M-Word × 18Bit)Direct Rambus DRAM Module(I/O Frequency:600MHz)(64M字節(32M字× 18位)直接Rambus 動態RAM模塊(I/O 頻率:600MHz))
THMR1E4-7 33,554,432-Word(64MBytes) by 18-Bit(32M-Word × 18Bit)Direct Rambus DRAM Module(I/O Frequency:711MHz)(64M字節(32M字× 18位)直接Rambus 動態RAM模塊(I/O 頻率:711MHz))
相關代理商/技術參數
參數描述
THMC51DBQR 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:
THMR1395 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Through Hole Power Inductors
THMR1395-0R6 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Through Hole Power Inductors
THMR1395-0R8 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Through Hole Power Inductors
THMR1395-1R2 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Through Hole Power Inductors