參數資料
型號： T491C474M035AS
廠商： KEMET Corporation
英文描述： Surface Mount Capacitors
中文描述： 表面貼裝電容
文件頁數： 7/100頁
文件大小： 4351K
代理商： T491C474M035AS
SOLID TANTALUM CHIP CAPACITORS
of equilibrium with the environment, is approxi-
mately -5% to +12% over the range from 25% to
95% RH, referred to the standard 50% RH. The
amount of change is dependent upon size (capaci-
tance and voltage rating, ie: CV product); small
sizes might change no more than ±5%.
Equilibrium at such extremes is seldom attained by
plastic-cased capacitors, and the change in
capacitance is consequently less. The rate of
response to humidity changes increases with
increasing temperature. Dissipation factor and
ESR also increase with increasing RH.
DC leakage current may rise upon exposure to a
combination of high temperature and high humidi-
ty, but is normally restored by voltage conditioning
under standard conditions. The increase will be
greater than that experienced under temperature
influence alone because of conduction through
absorbed water.
Tantalum chips may be affected by absorption of
water on external insulating surfaces.The water
film may also attract a layer of dust from the air,
increasing the effect. The most sensitive parame-
ter is leakage current.
4. Capacitance
0.1 μF to 1000 μF
Refer to part number tables for available capaci-
tance ratings and tolerances by series.
Capacitance is measured at 120 Hz, up to 1.0
volt rms maximum and up to 2.5 volts DC maximum, at
+25°C.DC bias causes only a small reduction in capaci-
tance, up to about 2% when full rated voltage is applied.
DC bias is not commonly used at room temperature, but
is more commonly used at elevated temperatures.
Capacitance decreases with increasing frequency.
FIGURE 1
Typical Effect of Frequency upon Capacitance
Capacitance increases with increasing temperature.
FIGURE 2
Typical Effect of Temperature upon Capacitance
Introduction
KEMET solid tantalum capacitors are identified by
the initial “T,” followed by a unique “Series” num-
ber; for example, T491, T492, etc. Each Series
denotes a general physical form and type of
encapsulation, as well as limits on dimensions and
certain electrical characteristics under standard
conditions of 25°C, 50% relative humidity, and one
atmosphere pressure. Specific requirements are
set forth in the respective Product Series in this
catalog. All series are 100% screened for leakage,
capacitance, dissipation factor, and ESR. All
Series are inspected to electrical limits using a
minimum .1% AQL sampling plan, according to
the Military Standard MIL-STD-105, even after
100% testing. This sampling plan, to the best of
KEMET Electronics’ knowledge, meets or exceeds
the generally accepted industry standard for simi-
lar products. KEMET capacitors may also be sup-
plied, with prior agreement, to meet specifications
with requirements differing from those of KEMET cat-
alogs.
ELECTRICAL
1. General Application Class
Solid tantalum capacitors are usually applied in
circuits where the AC component is small com-
pared to the DC component. Typical uses known
to KEMET Electronics include blocking, by-pass-
ing, decoupling, and filtering. They are also used in
timing circuits. General purpose devices are rec-
ommended to have an external series resistance of
0.1
/volt to reduce the failure due to surge cur-
rent. Newer devices designed for power applica-
tions (T495, T5XX), are built to eliminate this series
resistance requirement. Because tantalum capaci-
tors can experience scintillation (self-healing) in
their life, the circuit impedence should not exceed
100K
or this will circumvent the scintillation and
degrade leakage.
2. Operating Temperature Range
–55°C to +125°C
Voltage derating is specified in Section 5.
Performance characteristics over this temperature
range are presented within the following sections.
3. Non-Operating Temperature Range
–55°C to +125°C
Tantalum capacitors do not lose capacitance from
the “de-forming” effect as do liquid-electrolytic
capacitors. Storage at high temperature may
cause a small, temporary increase in leakage cur-
rent (measured under standard conditions), but the
original value is usually restored within a few min-
utes after application of rated voltage.
Tantalum chips are not hermetically sealed, there-
fore they do exhibit reversible changes in parame-
ters with respect to relative humidity (RH).
Capacitance increases with increasing humidity.
The limiting change, reached upon establishment
TANTALUM MnO
2
COMPONENT PERFORMANCE CHARACTERISTICS
+20%
+10%
0
-10%
-20%
-80
-60
-40
-20
Operating Temperature— C
0
+20
+60
+40
+80 +100 +120
P
C
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
5
S
相關PDF資料
PDF描述
T491C474M035AT Surface Mount Capacitors
T491D104K035AG Surface Mount Capacitors
T491D104K035AH Surface Mount Capacitors
T491D104K035AS Surface Mount Capacitors
T491D104K035AT Surface Mount Capacitors
相關代理商/技術參數
參數描述
T491C474M035AT 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:Surface Mount Capacitors
T491C474M050AT 功能描述:鉭質電容器-固體SMD 50volts 0.47uF 20% RoHS:否 制造商:AVX 電容:100 uF 電壓額定值:20 V ESR: 容差:10 % 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4.1 mm 制造商庫存號:E Case 工作溫度范圍:- 55 C to + 125 C 系列:TBM 產品:Tantalum Solid Low ESR Commercial Grade 封裝:Bulk
T491C474M050AT4394 制造商:KEMET Corporation 功能描述:.470UF 50.0V - Boxed Product (Development Kits)
T491C474M050ZT 功能描述:鉭質電容器-固體SMD .470UF 50.0V RoHS:否 制造商:AVX 電容:100 uF 電壓額定值:20 V ESR: 容差:10 % 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4.1 mm 制造商庫存號:E Case 工作溫度范圍:- 55 C to + 125 C 系列:TBM 產品:Tantalum Solid Low ESR Commercial Grade 封裝:Bulk
T491C474M050ZT7280 制造商:KEMET Corporation 功能描述:Cap Tant Solid 0.47uF 50V C CASE 20% (6 X 3.2 X 2.5mm) SMD 6032-28 125
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*