參數資料
型號： SX28AC/SSU
元件分類： 微控制器/微處理器
英文描述： 2 CHANNEL(S), I2C BUS CONTROLLER, PDSO28
封裝： GREEN, PLASTIC, SSOP-28
文件頁數： 10/48頁
文件大?。?/td> 772K
代理商： SX28AC/SSU
2005 Ubicom, Inc. All rights reserved.
- 18 -
www.ubicom.com
SX20AC/SX28AC
7.2 Port B MIWU/Interrupt Configuration
The WKPND_B register comes up with a random value
upon reset. The user program must clear the register
prior to enabling the wake-up condition or interrupts. The
proper initialization sequence is:
1. Select the desired edge (through WKED_B register).
2. Clear the WKPND_B register.
3. Enable the Wakeup condition (through WKEN_B regis-
ter).
Below is an example of how to read the WKPND_B regis-
ter to determine which Port B pin caused the wakeup or
interrupt, and to clear the WKPND_B register:
The final “mov” instruction in this example performs an
exchange of data between the working register (W) and
the WKPND_B register. This exchange occurs only with
Port B accesses. Otherwise, the “mov” instruction does
not perform an exchange, but only moves data from the
source to the destination.
Here is an example of a program segment that config-
ures the RB0, RB1, and RB2 pins to operate as Multi-
Input Wakeup/Interrupt pins, sensitive to falling edges:
To prevent false interrupts, the enabling step (clearing
bits in WKEN_B) should be done as the last step in a
sequence of Port B configuration steps. After this pro-
gram segment is executed, the device can receive inter-
rupts on the RB0, RB1, and RB2 pins. If the device is put
into the power down mode (by executing the SLEEP
instruction), the device can then receive wakeup signals
on those same pins.
mov
M,#$09
clr
W
mov
!RB,W
;W contains WKPND_B
;contents of W exchanged
;with contents of WKPND_B
mov M,#$0F ;prepare to write port data
;direction registers
mov W,#$07 ;load W with the value 07h
mov !RB,W
;configure RB0-RB2 to be inputs
mov M,#$0A ;prepare to write WKED_B
;(edge) register
;W contains the value 07h
mov !RB,W
;configure RB0-RB2 to sense
;falling edges
mov M,#$09 ;prepare to access WKPND_B
;(pending) register
mov W,#$00 ;clear W
mov !RB,W
;clear all wakeup pending bits
mov M,#$0B ;prepare to write WKEN_B (enable)
;register
mov W,#$F8h ;load W with the value F8h
mov !RB,W
;enable RB0-RB2 to operate as
;wakeup inputs
相關PDF資料
PDF描述
SY100EP11UZITR 100E SERIES, LOW SKEW CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8
SY100EP195VTCTR ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32
SY100EP195VTG ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32
SY100EP196VTCTR ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32
SY100EP196VTC ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32
相關代理商/技術參數
參數描述
SX28AD100-I/DP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug
SX28AD100-I/PQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug
SX28AD100-I/SO 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug
SX28AD100-I/SS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug
SX28AD100-I/TQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*