參數資料
型號： SI3220PPT0-EVB
廠商： Silicon Laboratories Inc
文件頁數： 50/112頁
文件大?。?/td> 0K
描述： BOARD EVAL W/SI3200 INTERFACE
標準包裝： 1
系列： ProSLIC®
主要目的： 接口，模擬前端（AFE）
已用 IC / 零件： Si3220
已供物品： 板，CD
Si3220/25 Si3200/02
42
Rev. 1.3
Not
Recommended
fo
r N
ew
D
esi
gn
s
3.9. Automatic Dual Battery Switching
The Dual ProSLIC chipsets provide the ability to switch
between several user-provided battery supplies to aid
thermal management. Two specific scenarios where
this method may be required follow:
Ringing to off-hook state transition (Si3220):
During the on-hook operating state, the Dual
ProSLIC chipset must operate from the ringing
battery supply to provide the desired ringing signal
when required. Once an off-hook condition is
detected, the Dual ProSLIC chipset must transition
to the lower battery supply (typically –24 V) to
reduce power dissipation during the active state. The
low current consumed by the Dual ProSLIC chipset
during the on-hook state results in very little power
dissipation while being powered from the ringing
battery supply, which can have an amplitude as high
as –100 V depending on the desired ringing
amplitude.
On-hook to off-hook state, short loop feed
(Si3225): When sourcing both long and short loop
lengths, the Dual ProSLIC chipset can automatically
switch from the typical –48 V off-hook battery supply
to a lower off-hook battery supply (e.g., –24 V) to
reduce the total off-hook power dissipation. The Dual
ProSLIC chipset continuously monitors the TIP-
RING voltage and selects the lowest battery voltage
required to power the loop when transitioning from
the on-hook to the off-hook state, thus assuring the
lowest power dissipation.
The BATSELa and BATSELb pins switch between the
two battery voltages based on the operating state and
the TIP-RING voltage. Figure 19 illustrates the chip
connections required to implement an automatic dual
battery switching scheme. When BATSEL is pulled
LOW, the desired channel is powered from the VBLO
supply. When BATSEL is pulled HIGH, the VBHI source
supplies power to the desired channel.
The BATSEL pins for both channels are controlled using
the BATSEL bit of the RLYCON register and can be
programmed to automatically switch to the lower battery
supply (VBLO) when the off-hook TIP-RING voltage is
low enough to allow proper operation from the lower
supply. When using the Si3220, this mode should
always be enabled to
allow seamless switching
between the ringing and off-hook states. The same
switching scheme is used with the Si3225 to reduce
power by switching to a lower off-hook battery when
sourcing a short loop.
Automatic battery selection should be disabled before
using the manual battery select control bit (BSEL bit,
Register 5—RLYCON,
bit 5).
Contact
Silicon
Laboratories
for
information
on
how
to
disable
automatic battery selection.
Two thresholds are provided to enable battery switching
with hysteresis. The BATHTH RAM location specifies
the threshold at which the Dual ProSLIC device
switches from the low battery (VBLO) to the high battery
(VBHI) due to an off-hook-to-on-hook transition. The
BATLTH RAM location specifies the threshold at which
the Si3220/Si3225 switches from VBHI to VBLO due to a
transition from the on-hook or ringing state to the off-
hook state or because the overhead during active Off-
Hook mode is sufficient to feed the subscriber loop
using a lower battery voltage.
The low-pass filter coefficient is calculated using the
following equation and is entered into the BATLPF RAM
location:
BATLPF = [(2
f x 4096)/800] x 23
Where f = the desired cutoff frequency of the filter
The programmable range of the filter is from 0h (blocks
all signals) to 4000h (unfiltered). A typical value of
10 Hz (0A10h) is sufficient to filter out any unwanted ac
artifacts while allowing the dc information to pass
through the filter.
Table 23 provides the register and RAM locations used
for programming the battery switching functions.
相關PDF資料
PDF描述
M3AAA-2640K IDC CABLE - MSC26A/MC26F/MSC26A
REC5-4805DRWZ/H6/A CONV DC/DC 5W 18-72VIN +/-05VOUT
SI3216MPPQ1-EVB BOARD EVAL W/SI3201 INTERFACE
VI-JVV-EZ-S CONVERTER MOD DC/DC 5.8V 25W
UUR1V101MNL1GS CAP ALUM 100UF 35V 20% SMD
相關代理商/技術參數
參數描述
SI3220PPT-EVB 制造商:SILABS 制造商全稱:SILABS 功能描述:EVALUATION BOARD FOR THE Si3220 DUAL PROSLIC
SI3220PPTX-EVB 功能描述:音頻 IC 開發工具 Si3220 Eval Board RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
SI3220-X-FQ 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC
SI3220-X-GQ 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC
SI3225 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*