參數資料
型號: SI3056DC-EVB
廠商: Silicon Laboratories Inc
文件頁數: 29/94頁
文件大?。?/td> 0K
描述: DAUGHTERCARD DAA SI3056/SI3018
標準包裝: 1
主要目的: 電信,數據采集裝置(DAA)
已用 IC / 零件: Si3056
已供物品: 板,CD
Si3056
Si3018/19/10
Rev. 1.05
35
5.22. Overload Detection
The Si3056 can be programmed to detect an overload
condition that exceeds the normal operating power
range of the DAA circuit. To use the overload detection
feature, the following steps should be followed:
1. Set the OH bit (Register 5, bit 0) to go off-hook, and
wait 25 ms to allow line transients to settle.
2. Enable overload detection by then setting the OPE
bit high (Register 17, bit 3).
If the DAA then senses an overload situation, it
automatically presents an 800
impedance to the line
to reduce the hookswitch current. At this time, the DAA
also sets the OPD bit (Register 19, bit 0) to indicate that
an overload condition exists. The line current detector
within the DAA has a threshold that is dependant upon
the ILIM bit (Register 26). When ILIM = 0, the overload
detection threshold equals 160 mA. When ILIM = 1, the
overload detection threshold equals 60 mA. The OPE
bit should always be cleared before going off-hook.
5.23. Gain Control
The Si3056 supports different gain and attenuation
settings depending on the line-side device being used.
For both devices, gains of 0, 3, 6, 9, and 12 dB can be
selected for the receive path with the ARX[2:0] bits. The
receive path can also be muted with the RXM bit.
Attenuations of 0, 3, 6, 9, and 12 dB can also be
selected for the transmit path with the ATX[2:0] bits. The
transmit path also can be muted with the TXM bit
(Register 15).
When using the Si3019 line-side device, the Si3056
provides even more flexible gain and attenuation
settings. The TXG2 and RXG2 bits (registers 38–39)
enable gain or attenuation in 1 dB increments up to
15 dB for the transmit and receive paths. The TGA2 and
RGA2 bits select either gain or attenuation for these
registers. The TXG3 and RXG3 bits (registers 40–41)
enable gain or attenuation in 0.1 dB increments up to
1.5 dB for the transmit and receive paths. The TGA3
and RGA3 bits select either gain or attenuation for these
registers. These additional gain/attenuation registers
are active only when the ARX[2:0] and ATX[2:0] bits are
set to all 0s.
Figure 24. Line-Side Device Signal Flow Diagram
Figure 25. Si3056 Signal Flow Diagram
To
Si3056
ADC
DAC
Link
Analog
Hybrid
ACT
TX
CO
Digital
Hybrid
IIRE
Digital
Filter
TXG2
To
Line-side
Device
Link
TXG3
TXA3
SDI
SDO
1 dB
Gain
Steps
0.1 dB
Gain/ATT
Steps
TXA2
1 dB
Attenuation
Steps
RXA2
1 dB
Attenuation
Steps
Digital
IIRE
Filter
RXG3
0.1 dB
Gain/ATT
Steps
RXA3
1 dB
Gain
Steps
RXG2
相關PDF資料
PDF描述
GBM31DCCI CONN EDGECARD 62POS R/A .156 SLD
CW252016-39NG INDUCTOR 39NH 1008 SMD
CW252016-33NG INDUCTOR 33NH 1008 SMD
CW252016-27NG INDUCTOR 27NH 1008 SMD
CW252016-22NG INDUCTOR 22NH 1008 SMD
相關代理商/技術參數
參數描述
Si3056-D-FS 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3056-D-FSR 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3056-D-ZS3R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET 56KBPS - Tape and Reel
SI3056-F-FS 制造商:Silicon Laboratories Inc 功能描述:
SI3056-FS 功能描述:IC SYSTEM-SIDE DAA 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21,V.22,V.23,V.29,V.32,V.34,V.90,V.92,Bell 103,Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574