參數資料
型號: SI3056DC-EVB
廠商: Silicon Laboratories Inc
文件頁數: 48/94頁
文件大?。?/td> 0K
描述: DAUGHTERCARD DAA SI3056/SI3018
標準包裝: 1
主要目的: 電信,數據采集裝置(DAA)
已用 IC / 零件: Si3056
已供物品: 板,CD
Si3056
Si3018/19/10
52
Rev. 1.05
Reset settings = 0000_0000
Register 4. Interrupt Source
Bit
D7D6D5
D4D3D2
D1
D0
Name
RDTI
ROVI
FDTI
BTDI
DODI
LCSOI
DLCSI
POLI
Type
R/W
Bit
Name
Function
7RDTI
Ring Detect Interrupt.
0 = A ring signal is not occurring.
1 = A ring signal is detected. If the RDTM (Register 3) and INTE (Register 2) bits are set a hard-
ware interrupt occurs on the AOUT/INT pin. This bit must be written to a 0 to be cleared. The RDI
bit (Register 2) determines if this bit is set only at the beginning of a ring pulse, or at the end of a
ring pulse as well. This bit should be cleared after clearing the PDL bit (Register 6) because pow-
ering up the line-side device may cause this interrupt to be triggered.
6ROVI
Receive Overload Interrupt.
0 = An excessive input level on the receive pin is not occurring.
1 = An excessive input level on the receive pin is detected. If the ROVM and INTE bits are set a
hardware interrupt occurs on the AOUT/INT pin. This bit must be written to 0 to clear it. This bit is
identical in function to the ROV bit (Register 17). Clearing this bit also clears the ROV bit.
5FDTI
Frame Detect Interrupt
.
0 = Frame detect is established on the communications link.
1 = This bit is set when the communications link does not have frame lock. If the FDTM and INTE
bits are set, a hardware interrupt occurs on the AOUT/INT pin. Once set, this bit must be written
to a 0 to be cleared.
4BTDI
Billing Tone Detect Interrupt.
0 = A billing tone has not occurred.
1 = A billing tone has been detected. If the BTDM and INTE bits are set, a hardware interrupt
occurs on the AOUT/INT pin. This bit must be written to 0 to clear it.
3DODI
Drop Out Detect Interrupt
.
0 = The line-side power supply has not collapsed.
1 = The line-side power supply has collapsed (The DOD bit in Register 19 has fired). If the
DODM and INTE bits are set, a hardware interrupt occurs on the AOUT/INT pin. This bit must be
written to 0 to be cleared. This bit should be cleared after clearing the PDL bit (Register 6)
because powering as the line-side device can cause this interrupt to be triggered.
2LCSOI
Loop Current Sense Overload Interrupt
.
0 = The LCS bits have not reached max value (all ones).
1 = The LCS bits have reached max value. If the LCSOM bit (Register 3) and the INTE bit are
set, a hardware interrupt occurs on the AOUT/INT pin. This bit must be written to 0 to be cleared.
LCSOI does not necessarily imply that an overcurrent situation has occurred. An overcurrent sit-
uation in the DAA is determined by the status of the OPD bit (Register 19). After the LCSOI inter-
rupt fires, the OPD bit should be checked to determine if an overcurrent situation exists.
相關PDF資料
PDF描述
GBM31DCCI CONN EDGECARD 62POS R/A .156 SLD
CW252016-39NG INDUCTOR 39NH 1008 SMD
CW252016-33NG INDUCTOR 33NH 1008 SMD
CW252016-27NG INDUCTOR 27NH 1008 SMD
CW252016-22NG INDUCTOR 22NH 1008 SMD
相關代理商/技術參數
參數描述
Si3056-D-FS 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3056-D-FSR 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3056-D-ZS3R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET 56KBPS - Tape and Reel
SI3056-F-FS 制造商:Silicon Laboratories Inc 功能描述:
SI3056-FS 功能描述:IC SYSTEM-SIDE DAA 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21,V.22,V.23,V.29,V.32,V.34,V.90,V.92,Bell 103,Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574