參數資料
型號： SC28L202A1
廠商： NXP Semiconductors N.V.
英文描述： Dual universal asynchronous receiver/transmitter DUART
中文描述： 雙路通用異步接收器/發送器杜阿爾特
文件頁數： 37/77頁
文件大?。?/td> 531K
代理商： SC28L202A1
Philips Semiconductors
Objective specification
SC28L202
Dual UART
2000 Feb 10
31
IMR – Interrupt Mask Register A and B
Bit 7
I/O Port Change of state
Bit 6
Rx Watch–dog
Time–out
Bit 5
Address
recognition event
Bit 4
Xon/off
event
Bit 3
C/T
Ready
Bit 2
Break Change
Of State
Bit 1
RxRDY
interrupt
Bit 0
TxRDY
interrupt
The programming of this register selects which bits in the ISR cause
an interrupt output. If a bit in the ISR is a ’1’ and the corresponding
bit in the IMR is a ’1’, the interrupt source is presented to the internal
interrupt arbitration circuits, eventually resulting in the IRQN output
being asserted (low). If the corresponding bit in the IMR is a zero,
the state of the bit in the ISR has no affect on the IRQN output.
IMR[7] COS enable
Allows a change of state in the inputs equipped with input change
detectors to cause an interrupt.
IMR[6] Fixed Watchdog Enable
Controls the generation of an interrupt watchdog timer event. If set,
a count of 64 idle bit times in the receiver will begin interrupt
arbitration.
IMR[5] Address recognition enable
Enables the generation of an interrupt in response to changes in the
Address Recognition circuitry of the Special Mode (multi–drop or
wake–up mode).
IMR[4] Xon/Xoff Enable
Enables the generation of an interrupt in response to recognition of
an in–band flow control character.
IMR[3] Counter/Timer Enable
Enable the C/T interrupt when the C/T reaches 0 count.
[2]
Enables
the generation of an interrupt when a Break condition has been
detected by the channel receiver.
IMR[1] Receiver (Rx) Enable
Enables the generation of an interrupt when servicing for the
RxFIFO is desired.
IMR[0] Transmitter (Tx) Enable
Enables the generation of an interrupt when servicing for the
TxFIFO is desired.
RxFIFO – Receiver FIFO, A and B
Bit[10]
These bits are sent to the status register
Break
Received Status
Bit[9]
Bit[8]
Bits [7:0]
This the data byte sent to the data bus or RxFIFO read
8 data bits
MSBs =0 for 7,6,5 bit data
Framing
Error Status
Parity
Error Status
The FIFO for the receiver is 11 bits wide and 256 ”words” deep. The
status of each byte received is stored with that byte and is moved
along with the byte as the characters are read from the FIFO. The
upper three bits are presented in the STATUS register and they
change in the status register each time a data byte is read from the
FIFO. Therefor the status register should be read BEFORE the byte
is read from the RxFIFO if one wishes to ascertain the quality of the
byte
The foregoing applies to the ”character error” mode of status
reporting. See MR1[5] and ”RxFIFO Status” descriptions for ”block
error” status reporting. Briefly, ”Block Error” gives the accumulated
error of all bytes received by the RxFIFO since the last “Reset Error”
command was issued. (CR = 0x04)
TxFIFO – Transmitter FIFO, A and B
Bits 7:0
8 data bits. MSBs set to 0 for 7, 6, 5 bit data
The FIFO for the transmitter is 8 bits wide by 256 bytes deep. For character lengths less than 8 bits the upper bits will be ignored by the
transmitter state machine and thus are effectively discarded.
RxFIL – Receiver FIFO Interrupt Level, A and B
Bits 7:0
Any one of 256 FIFO fill positions
The position in the Rx FIFO that causes the receiver will enter the interrupt arbitration process. This register is used to offset the effect of the
arbitration threshold. It use may yield moderate improvements in the interrupt service. It will also “equalize” interrupt latency and allow for larger
aggregate block transfers between fast and slow channels. Writing to this register removes the interrupt control established in MR0 and MR1.
RxFL – Receiver FIFO Fill Level Register
Bits 7:0
Channel byte count code ** (1) = implied ‘1’
00000001 = 1
00000010 = 2
to
11111111 = 255
**(1)00000000 = 256 if RxRDY status bit is set.
The number of bytes filled in the receiver FIFO
相關PDF資料
PDF描述
SC28L202 Dual universal asynchronous receiver/transmitter DUART
SC28L202A1B Dual universal asynchronous receiver/transmitter DUART
SC28L202A1D Dual universal asynchronous receiver/transmitter DUART
SC431CS8DE2 Analog IC
SC431CS8DE3 Analog IC
相關代理商/技術參數
參數描述
SC28L202A1B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual universal asynchronous receiver/transmitter DUART
SC28L202A1D 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual universal asynchronous receiver/transmitter DUART
SC28L202A1DGG 功能描述:UART 接口集成電路 3-5V 2CH UART 3MBPS 256B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L202A1DGG,112 功能描述:UART 接口集成電路 3-5V 2CH UART 3MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L202A1DGG,118 功能描述:UART 接口集成電路 3-5V 2CH UART 3MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*