參數資料
型號： SC16C850IET,115
廠商： NXP Semiconductors
文件頁數： 11/55頁
文件大?。?/td> 0K
描述： IC UART SINGLE W/FIFO 36-TFBGA
標準包裝： 1,000
特點： 可編程
通道數： 1，UART
FIFO's： 128 字節
規程： RS485
電源電壓： 2.5 V ~ 3.3 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 36-TFBGA
供應商設備封裝： 36-TFBGA（3.5x3.5）
包裝： 帶卷 (TR)
其它名稱： 935284685115
SC16C850IET-G
SC16C850IET-G-ND
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
19 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
6.13 RS-485 features
6.13.1 Auto RS-485 RTS control
Normally the RTS pin is controlled by MCR[1], or if hardware flow control is enabled, the
logic state of the RTS pin is controlled by the hardware flow control circuitry. AFCR2[4] will
take the precedence over the other two modes; once this bit is set, the transmitter will
control the state of the RTS pin. The transmitter automatically asserts the RTS pin
(logic 0) once the host writes data to the transmit FIFO, and de-asserts RTS pin (logic 1)
once the last bit of the data has been transmitted.
To use the auto RS-485 RTS mode the software would have to disable the hardware
flow control function.
6.13.2 RS-485 RTS inversion
AFCR2[5] reverses the polarity of the RTS pin if the UART is in auto RS-485 RTS mode.
When the transmitter has data to be sent it will de-asserts the RTS pin (logic 1), and when
the last bit of the data has been sent out the transmitter asserts the RTS pin (logic 0).
6.13.3 Auto 9-bit mode (RS-485)
AFCR2[0] is used to enable the 9-bit mode (Multi-drop or RS-485 mode). In this mode of
operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the automatic 9-bit mode, the software would have to disable the hardware and
software flow control functions.
6.13.3.1
Normal Multi-drop mode
The 9-bit Mode in AFCR2[0] is enabled, but not Special Character Detect (EFR[5]). The
receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER[2] must be set to ‘1’ at this
time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message
from the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller takes no further action, and the receiver
will receive the subsequent data.
相關PDF資料
PDF描述
MS27508E12B22SC CONN RCPT 22POS BOX MNT W/SCKT
MS27484P12B35S CONN PLUG 22POS STRAIGHT W/SCKT
MS27474P12B98P CONN RCPT 10POS JAM NUT W/PINS
D38999/24WD15PN CONN RCPT 15POS JAM NUT W/PINS
MS3116F-14-19S CONN PLUG 19POS W/SOCKET SOLDER
相關代理商/技術參數
參數描述
SC16C850IET-G 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850IET-S 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850L 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V single UART, 5 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface
SC16C850LIB,128 制造商:NXP Semiconductors 功能描述:
SC16C850LIB,151 制造商:NXP Semiconductors 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*