參數資料
型號: SC16C650BIN40,112
廠商: NXP Semiconductors
文件頁數: 48/48頁
文件大?。?/td> 0K
描述: IC UART SINGLE W/FIFO 40-DIP
標準包裝: 9
通道數: 1,UART
FIFO's: 32 字節
電源電壓: 2.5V,3.3V,5V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 通孔
封裝/外殼: 40-DIP(0.600",15.24mm)
供應商設備封裝: 40-DIP
包裝: 管件
其它名稱: 568-2045-5
935274389112
SC16C650BIN40
SC16C650B_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 14 September 2009
9 of 48
NXP Semiconductors
SC16C650B
UART with 32-byte FIFOs and IrDA encoder/decoder
6.1 Internal registers
The SC16C650B provides 17 internal registers for monitoring and control. These registers
are shown in Table 3. Twelve registers are similar to those already available in the
standard 16C550. These registers function as data holding registers (THR/RHR), interrupt
status and control registers (IER/ISR), a FIFO control register (FCR), line status and
control registers (LCR/LSR), modem status and control registers (MCR/MSR),
programmable data rate (clock) control registers (DLL/DLM), and a user accessible
ScratchPad Register (SPR). Beyond the general 16C550 features and capabilities, the
SC16C650B offers an enhanced feature register set (EFR, Xon1/Xoff1, Xon2/Xoff2) that
provides on-board hardware/software ow control. Register functions are more fully
described in the following paragraphs.
[1]
These registers are accessible only when LCR[7] is a logic 0.
[2]
These registers are accessible only when LCR[7] is a logic 1.
[3]
Enhanced Feature Register, Xon1, Xon2 and Xoff1, Xoff2 are accessible only when the LCR is set to BFh.
6.2 FIFO operation
The 32-byte transmit and receive data FIFOs are enabled by the FIFO Control Register
bit 0 (FCR[0]). With 16C550 devices, the user can set the receive trigger level, but not the
transmit trigger level. The SC16C650B provides independent trigger levels for both
receiver and transmitter. To remain compatible with SC16C550, the transmit interrupt
trigger level is set to 16 following a reset. It should be noted that the user can set the
transmit trigger levels by writing to the FCR register, but activation will not take place until
EFR[4] is set to a logic 1. The receiver FIFO section includes a time-out function to ensure
Table 3.
Internal registers decoding
A2
A1
A0
Read mode
Write mode
General register set (THR/RHR, IER/ISR, MCR/MSR, FCR, LCR/LSR, SPR)[1]
0
Receive Holding Register
Transmit Holding Register
0
1
Interrupt Enable Register
0
1
0
Interrupt Status Register
FIFO Control Register
0
1
Line Control Register
1
0
Modem Control Register
1
0
1
Line Status Register
n/a
1
0
Modem Status Register
n/a
1
Scratchpad Register
Baud rate register set (DLL/DLM)[2]
0
LSB of Divisor Latch
0
1
MSB of Divisor Latch
Enhanced register set (EFR, Xon1, Xoff1, Xon2, Xoff2)[3]
0
1
0
Enhanced Feature Register
1
0
Xon1 word
1
0
1
Xon2 word
1
0
Xoff1 word
1
Xoff2 word
相關PDF資料
PDF描述
V24C24H150BL CONVERTER MOD DC/DC 24V 150W
SC16C554IB64,157 IC UART QUAD W/FIFO 64-LQFP
V24C24H150B3 CONVERTER MOD DC/DC 24V 150W
ATMEGA644V-10MUR MCU AVR 64K FLASH 10MHZ 44QFN
SC28C94A1N,112 IC UART QUAD W/FIFO 48-DIP
相關代理商/技術參數
參數描述
SC16C652 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 32 bytes of transmit and receive FIFOs
SC16C652B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
SC16C652BIB48 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIB48,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIB48,151 功能描述:UART 接口集成電路 2CH. UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel