參數資料
型號: SC16C550BIN40,112
廠商: NXP Semiconductors
文件頁數: 45/48頁
文件大?。?/td> 0K
描述: IC UART 40-DIP
標準包裝: 9
特點: 可編程
通道數: 1,UART
FIFO's: 16 字節(jié)
電源電壓: 2.5V,3.3V,5V
帶自動流量控制功能:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 通孔
封裝/外殼: 40-DIP(0.600",15.24mm)
供應商設備封裝: 40-DIP
包裝: 管件
其它名稱: 935274386112
SC16C550BIN40
SC16C550BIN40-ND
SC16C550B_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 1 October 2008
6 of 48
NXP Semiconductors
SC16C550B
5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
5.2 Pin description
Table 2.
Pin description
Symbol
Pin
Type
Description
PLCC44 LQFP48 DIP40 HVQFN32
A0
31
28
19
I
Register select. A2 to A0 are used during read and write
operations to select the UART register to read from or
write to. Refer to Table 3 for register addresses and refer to
AS description.
A1
30
27
18
A2
29
26
17
AS
28
24
25
-
I
Address strobe. When AS is active (LOW), A0, A1, and
A2 and CS0, CS1, and CS2 drive the internal select logic
directly; when AS is HIGH, the register select and chip
select signals are held at the logic levels they were in when
the LOW-to-HIGH transition of AS occurred.
BAUDOUT
17
12
15
-
O
Baud out. BAUDOUT is a 16
× clock signal for the
transmitter section of the UART. The clock rate is
established by the reference oscillator frequency divided
by a divisor specied in the baud generator divisor latches.
BAUDOUT may also be used for the receiver section by
tying this output to RCLK. In HVQFN32 package
BAUDOUT and RCLK are bonded internally.
CS0[2]
14
9
12
-
I
Chip select. When CS0 and CS1 are HIGH and CS2 is
LOW, these three inputs select the UART. When any of
these inputs are inactive, the UART remains inactive (refer
to AS description).
CS1[2]
15
10
13
-
CS2[2]
16
11
14
-
CS[2]
---
8
40
38
36
24
I
Clear to send. CTS is a modem status signal. Its condition
can be checked by reading bit 4 (CTS) of the Modem
Status Register. Bit 0 (CTS) of the Modem Status Register
indicates that CTS has changed states since the last read
from the Modem Status Register. If the modem status
interrupt is enabled when CTS changes levels and the
auto-CTS mode is not enabled, an interrupt is generated.
This pin has no effect on the UART’s transmit or receive
operation.
D7 to D0
9, 8, 7,
6, 5, 4,
3, 2
4, 3, 2,
47, 46,
45, 44,
43
8, 7,
6, 5,
4, 3,
2, 1
5, 4, 3, 1,
32, 31,
30, 29
I/O
Data bus. Eight data lines with 3-state outputs provide a
bidirectional path for data, control and status information
between the UART and the CPU.
DCD[2]
42
40
38
26
I
Data carrier detect. DCD is a modem status signal. Its
condition can be checked by reading bit 7 (DCD) of the
Modem Status Register. Bit 3 (DCD) of the Modem Status
Register indicates that DCD has changed states since the
last read from the Modem Status Register. If the modem
status interrupt is enabled when DCD changes levels, an
interrupt is generated.
DDIS
26
22
23
-
O
Driver disable. DDIS is active (LOW) when the CPU is
reading data. When inactive (HIGH), DDIS can disable an
external transceiver.
相關PDF資料
PDF描述
MS27473P16A35S CONN PLUG 55POS STRAIGHT W/SCKT
MS27473T16B8S CONN PLUG 8POS STRAIGHT W/SCKT
D38999/24WE26PN CONN RCPT 26POS JAM NUT W/PINS
D38999/24FD5PB CONN RCPT 5POS JAM NUT W/PINS
MS27473E16B35PA CONN PLUG 55POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
SC16C550IA44 制造商:NXP Semiconductors 功能描述:UART 16BYTE FIFO 16C550 PLCC44
SC16C550IA44,512 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550IA44,518 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550IA44,529 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550IB48 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder