- 您現在的位置：買賣IC網 > PDF目錄372121 > SC16C2550B (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C2550B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5雙UART /秒（最大），16字節的FIFO |
| 文件頁數： | 37/42頁 |
| 文件大?。?/td> | 200K |
| 代理商： | SC16C2550B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁
Philips Semiconductors
SC16C2550B
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Product data
Rev. 02 — 14 December 2004
37 of 42
9397 750 14449
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
12. Soldering
12.1 Introduction
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all IC packages. Wave soldering is often
preferred when through-hole and surface mount components are mixed on one
printed-circuit board. Wave soldering can still be used for certain surface mount ICs,
but it is not suitable for fine pitch SMDs. In these situations reflow soldering is
recommended. Driven by legislation and environmental forces the worldwide use of
lead-free solder pastes is increasing.
12.2 Through-hole mount packages
12.2.1
Soldering by dipping or by solder wave
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250
°
C or
265
°
C, depending on solder material applied, SnPb or Pb-free respectively.
The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the
plastic body must not exceed the specified maximum storage temperature (T
stg(max)
).
If the printed-circuit board has been pre-heated, forced cooling may be necessary
immediately after soldering to keep the temperature within the permissible limit.
12.2.2
Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron
bit is less than 300
°
C it may remain in contact for up to 10 seconds. If the bit
temperature is between 300 and 400
°
C, contact may be up to 5 seconds.
12.3 Surface mount packages
12.3.1
Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270
°
C depending on solder
paste material. The top-surface temperature of the packages should preferably be
kept:
below 225
°
C (SnPb process) or below 245
°
C (Pb-free process)
–
for all the BGA and SSOP-T packages
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C2550BIN40 | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs |
| SC16C2550IA44 | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder |
| SC16C2550IN40 | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder |
| SC16C2550 | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder |
| SC16C2550IB48 | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder-decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C2550B_07 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs |
| SC16C2550BIA44 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550BIA44,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550BIA44,518 | 功能描述:UART 接口集成電路 2CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550BIA44,518-CUT TAPE | 制造商:NXP 功能描述:SC16C2550B 5 V 3.3 V and 2.5 V Dual UART 5 Mbit/s w/ 16-byte FIFOs - PLCC44 |
發布緊急采購，3分鐘左右您將得到回復。