參數資料
型號： SAA567X
廠商： NXP Semiconductors N.V.
英文描述： Enhanced TV microcontrollers with On-Screen Display (OSD)
中文描述： 與微控制器在強化電視屏幕顯示（OSD）
文件頁數： 49/116頁
文件大?。?/td> 532K
代理商： SAA567X
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
2002 May 06
49
Philips Semiconductors
Objective specification
Enhanced TV microcontrollers with
On-Screen Display (OSD)
SAA567x; SAA569x
18.4
UART baud rates
For full details on the UART operation, refer to “Handbook
IC20, 80C51-Based 8-bit Microcontrollers”
Remark:
f
clk
used in the following calculations refers to the
microcontroller clock frequency (12 MHz). The SAA56xx
family of devices uses both clock edges, so the division
factor is 6 instead of 12.
The serial port can operate with different baud rates,
depending on its mode:
Mode 0
(SM0 = 0, SM1 = 0): in shift register mode the
baud rate is fixed at
1
6
f
clk
.
Mode 2
(SM0 = 0, SM1 = 0): in this fixed baud rate
mode, the baud rate is determined by the SMOD bit in
the PCON register: baud rate =
Modes 1
(SM0 = 0, SM1 = 1)
and 3
(SM0 = 1,
SM1 = 1): in these modes, the baud rate is variable and
is determined by either Timer 1 or Timer 2;
see Chapter 13.
Timer 1
: can be used in either Timer or Counter mode
where the baud rate is determined by the timer overflow
rate and the value of SMOD as follows:
SMOD
32
i.e. baud rate =
where T1H is the decimal value of the register contents.
When Timer 1 is configured for timer operation it is normal
to use the 8-bit auto-reload mode. However, 16-bit mode
can be used for very low baud rates. In this case the
Timer 1 interrupt will need to do a 16-bit software reload.
Timer 2
: will be placed in baud generator mode when the
RCLK0 and/or TCLK0 bits in the T2CON register are set.
When Timer 2 is clocked internally the baud rate
f
16
65536
T2H, T2L
(
–
[
×
=
:
Where T2H, T2L is the decimal value of the 16-bit contents
of the T2H, T2L SFRs.
When Timer 2 is configured as a counter, using pin T2
then the baud rate is the Timer 2 overflow rate divided
by 16
19 LED SUPPORT
Port pins P0.5 and P0.6 have an 8 mA current sinking
capability to enable LEDs in series with current limiting
resistors to be driven directly, without the need for
additional buffering circuits.
20 EXTERNAL SRAM AND ROM INTERFACE
The external address/data bus of the 80C51
microprocessor may be interfaced to:
Additional SRAM Data memory for multi-page
acquisition applications
External Program ROM.
The application circuit can be achieved using either the
multiplexed address and data I/O or the de-multiplexed
address and data I/O.
External SRAM data memory
: It is possible to interface
up to 256 kbytes of external data memory using pins
RAMBK<1:0> and A15_BK. Each of the four Data memory
banks is selected by RAMBK<1:0> (SFR ROMBK<4:3>);
see Table 21.
Figure 12 shows an example of the interfacing
connections for external SRAM data memory; see also
Chapter 30.
Table 21
RAMBK selection
External program ROM
(pin EA tied LOW): for the
SAA567x; SAA569x family of devices only, it is possible to
interface up to 256 kbytes of external program ROM,
which is addressed using the contiguous address bus.
Figure 13 shows the interface connections.
Remark:
pins A15_BK, ROMBK0, ROMBK1 and
ROMBK2 are used for emulating the external program
ROM.
Internal program ROM
(pin EA tied HIGH): for the
SAA567x; SAA569x family of devices only, there is
rollover to external ROM which allows up to a maximum of
256 kbytes of program ROM (e.g. 192 kbytes internal plus
64 kbytes external). Figures 14 show the interface
connections.
SMOD
32
2
f
clk
×
baud rate
2
Timer 1 overflow rate
×
=
SMOD
32
2
f
6
256
T1H
–
(
)
×
------------------------------------------
×
)
]
----------------------------------------------------------------------
RAMBK<1:0>
BANK
EXTERNAL
ADDRESS RANGE
00
01
10
11
Bank 0
Bank 1
Bank 2
Bank 3
0 to 64 kbytes
64 to 128 kbytes
128 to 192 kbytes
192 to 256 kbytes
相關PDF資料
PDF描述
SAA5695HL Enhanced TV microcontrollers with On-Screen Display (OSD)
SAA569x Enhanced TV microcontrollers with On-Screen Display (OSD)
SAA5677HL Enhanced TV microcontrollers with On-Screen Display (OSD)
SAA5700GP Chinese Character System Teletext CCST decoder
SAA5700 Chinese Character System Teletext CCST decoder
相關代理商/技術參數
參數描述
SAA5695HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display (OSD)
SAA5697HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display (OSD)
SAA569X 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display (OSD)
SAA5700 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Chinese Character System Teletext CCST decoder
SAA5700GP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Chinese Character System Teletext CCST decoder
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*