參數資料
型號： S80C32-44:RD
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, 44 MHz, MICROCONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 55/152頁
文件大?。?/td> 2528K
148
2486AA–AVR–02/2013
ATmega8(L)
USART Register
Description
USART I/O Data
Register – UDR
The USART Transmit Data Buffer Register and USART Receive Data Buffer Registers share the
same I/O address referred to as USART Data Register or UDR. The Transmit Data Buffer Reg-
ister (TXB) will be the destination for data written to the UDR Register location. Reading the
UDR Register location will return the contents of the Receive Data Buffer Register (RXB).
For 5-bit, 6-bit, or 7-bit characters the upper unused bits will be ignored by the Transmitter and
set to zero by the Receiver.
The transmit buffer can only be written when the UDRE Flag in the UCSRA Register is set. Data
written to UDR when the UDRE Flag is not set, will be ignored by the USART Transmitter. When
data is written to the transmit buffer, and the Transmitter is enabled, the Transmitter will load the
data into the Transmit Shift Register when the Shift Register is empty. Then the data will be seri-
ally transmitted on the TxD pin.
The receive buffer consists of a two level FIFO. The FIFO will change its state whenever the
receive buffer is accessed. Due to this behavior of the receive buffer, do not use Read-Modify-
Write instructions (SBI and CBI) on this location. Be careful when using bit test instructions
(SBIC and SBIS), since these also will change the state of the FIFO.
USART Control and
Status Register A –
UCSRA
Bit 7 – RXC: USART Receive Complete
This flag bit is set when there are unread data in the receive buffer and cleared when the receive
buffer is empty (that is, does not contain any unread data). If the Receiver is disabled, the
receive buffer will be flushed and consequently the RXC bit will become zero. The RXC Flag can
be used to generate a Receive Complete interrupt (see description of the “Bit 7 – RXCIE: RX
Bit 6 – TXC: USART Transmit Complete
This flag bit is set when the entire frame in the Transmit Shift Register has been shifted out and
there are no new data currently present in the transmit buffer (UDR). The TXC Flag bit is auto-
matically cleared when a transmit complete interrupt is executed, or it can be cleared by writing
a one to its bit location. The TXC Flag can generate a Transmit Complete interrupt (see descrip-
Bit 5 – UDRE: USART Data Register Empty
The UDRE Flag indicates if the transmit buffer (UDR) is ready to receive new data. If UDRE is
one, the buffer is empty, and therefore ready to be written. The UDRE Flag can generate a Data
Register Empty interrupt (see description of the “Bit 5 – UDRIE: USART Data Register Empty
UDRE is set after a reset to indicate that the Transmitter is ready.
Bit
76543210
RXB[7:0]
UDR (Read)
TXB[7:0]
UDR (Write)
Read/Write
R/W
Initial Value
00000000
Bit
765
4321
0
RXC
TXC
UDRE
FE
DOR
PE
U2X
MPCM
UCSRA
Read/Write
R
R/W
R
R/W
Initial Value
001
0000
0
相關PDF資料
PDF描述
MQ80C52XXX-36/883 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
S80C32-L16D 8-BIT, 16 MHz, MICROCONTROLLER, PQCC44
MP80C51C-36D 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PDIP40
MR80C52EXXX-16SHXXX:R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44
MD83C154DCXXX-25P883D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
S80C32-L16 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
S80C32-L16R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
S80C376CB8 WAF 制造商:Intel 功能描述:
S80C42 制造商:Intel 功能描述:
S80C51 WAF 制造商:Intel 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*