參數資料
型號： S80C32-44:RD
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, 44 MHz, MICROCONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 38/152頁
文件大?。?/td> 2528K
132
2486AA–AVR–02/2013
ATmega8(L)
Note:
1. The baud rate is defined to be the transfer rate in bit per second (bps)
BAUD Baud rate (in bits per second, bps)
fOSC
System Oscillator clock frequency
UBRR Contents of the UBRRH and UBRRL Registers (0 - 4095)
Some examples of UBRR values for some system clock frequencies are found in Table 60 on
Double Speed
Operation (U2X)
The transfer rate can be doubled by setting the U2X bit in UCSRA. Setting this bit only has effect
for the asynchronous operation. Set this bit to zero when using synchronous operation.
Setting this bit will reduce the divisor of the baud rate divider from 16 to 8, effectively doubling
the transfer rate for asynchronous communication. Note however that the Receiver will in this
case only use half the number of samples (reduced from 16 to 8) for data sampling and clock
recovery, and therefore a more accurate baud rate setting and system clock are required when
this mode is used. For the Transmitter, there are no downsides.
External Clock
External clocking is used by the Synchronous Slave modes of operation. The description in this
section refers to Figure 62 on page 131 for details.
External clock input from the XCK pin is sampled by a synchronization register to minimize the
chance of meta-stability. The output from the synchronization register must then pass through
an edge detector before it can be used by the Transmitter and Receiver. This process intro-
duces a two CPU clock period delay and therefore the maximum external XCK clock frequency
is limited by the following equation:
Note that f
osc depends on the stability of the system clock source. It is therefore recommended to
add some margin to avoid possible loss of data due to frequency variations.
Synchronous Clock
Operation
When Synchronous mode is used (UMSEL = 1), the XCK pin will be used as either clock input
(Slave) or clock output (Master). The dependency between the clock edges and data sampling
or data change is the same. The basic principle is that data input (on RxD) is sampled at the
opposite XCK clock edge of the edge the data output (TxD) is changed.
Table 52. Equations for Calculating Baud Rate Register Setting
Operating Mode
Equation for Calculating
Baud Rate(1)
Equation for Calculating
UBRR Value
Asynchronous Normal mode
(U2X = 0)
Asynchronous Double Speed
Mode (U2X = 1)
Synchronous Master Mode
BAUD
fOSC
16
UBRR 1
+
---------------------------------------
=
UBRR
fOSC
16
BAUD
------------------------
1
–
=
BAUD
fOSC
8
UBRR 1
+
-----------------------------------
=
UBRR
fOSC
8
BAUD
--------------------
1
–
=
BAUD
fOSC
2
UBRR 1
+
-----------------------------------
=
UBRR
fOSC
2
BAUD
--------------------
1
–
=
fXCK
fOSC
4
-----------
相關PDF資料
PDF描述
MQ80C52XXX-36/883 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
S80C32-L16D 8-BIT, 16 MHz, MICROCONTROLLER, PQCC44
MP80C51C-36D 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PDIP40
MR80C52EXXX-16SHXXX:R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44
MD83C154DCXXX-25P883D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
S80C32-L16 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
S80C32-L16R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
S80C376CB8 WAF 制造商:Intel 功能描述:
S80C42 制造商:Intel 功能描述:
S80C51 WAF 制造商:Intel 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*