- 您現在的位置：買賣IC網 > PDF目錄374668 > S5935_07 (Applied Micro Circuits Corp.) PCI Product PDF資料下載
參數資料
| 型號： | S5935_07 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | PCI Product |
| 中文描述： | 的PCI產品 |
| 文件頁數： | 146/204頁 |
| 文件大?。?/td> | 1897K |
| 代理商： | S5935_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁當前第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁
S5935 – PCI Product
146 DS1527
AMCC Confidential and Proprietary
Revision 1.02 – June 27, 2006
Data Book
Some applications hold the RDFIFO# and WRFIFO#
inputs active for a synchronous interface. In 16-bit
mode, designs must avoid writing to a full FIFO. The
data for the write is lost, but the internal mechanism to
direct the 16-bit external data bus to the upper 16-bits
of the FIFO register is triggered. This creates a situa-
tion where the FIFO is out of step. The next 16-bit
FIFO write is directed to the upper 16-bits of the FIFO,
and the FIFO advances incorrectly. The WRFULL out-
put should be used to gate the WRFIFO# input to
avoid this situation. A similar problem can occur if
Add-On logic attempts to read an empty FIFO in 16-bit
mode. RDEMPTY should be used to gate the
RDFIFO# input to avoid problems with the FIFO get-
ting out of step. In 32-bit mode (MODE = low), these
situations do not occur.
If FIFO accesses are done without the direct access
signals with MODE configured for 16-bits (using ADR,
SELECT#, etc.), external hardware must toggle ADR1
between consecutive 16-bit bus cycles. The FIFO
advance condition must be set to correspond to the
order the application accesses the upper and lower
words in the FIFO register.
CONFIGURATION
The FIFO configuration takes place during initialization
and during operation. During initialization, the bus
master register access rights are defined. During oper-
ation, FIFO advance conditions, endian conversion,
and bus mastering capabilities are defined. The follow-
ing section describes the bits and registers which are
involved with controlling and monitoring FIFO
operation.
FIFO Setup During Initialization
Location 45h in an external non-volatile memory may
be used to configure the S5935 FIFO during initializa-
tion. If no external non-volatile memory is used, FIFO
operation is disabled.
The value of bit 7 in location 45h determines if the
address and transfer count registers used in bus mas-
tering are accessible from the PCI bus or from the
Add-On bus. Once the configuration information is
downloaded from non-volatile memory after reset, the
bus mastering initialization method can not be
changed. Access to the bus master address and trans-
fer count registers cannot be alternated between the
PCI bus and the Add-On interface during operation.
Bits 6 and 5 in location 45h enable FIFO register
accesses using the RDFIFO#, WRFIFO#, RD# and
WR# inputs synchronous to BPCLK. For synchronous
operation, RDFIFO#, WRFIFO#, RD# and WR# oper-
ate as enables, using BPCLK to clock data.
FIFO Status and Control Bits
The FIFO status can be monitored and the FIFO oper-
ation controlled from the PCI Operation Registers and/
or the Add-On Operation Registers. The FIFO register
resides at offset 20h in the PCI and Add-On Operation
Registers.
The Bus Master Control/Status (MCSR) PCI Operation
register allows a PCI host to monitor FIFO activity and
control FIFO operation. Reset controls allow the PCI to
Add-On FIFO and Add-On to PCI FIFO flags to be
reset (individually). Status bits indicate if the PCI to
Add-On FIFO is empty, has four or more open spaces,
or is full. Status bits also indicate if the Add-On to PCI
FIFO is empty, has four or more full locations or is full.
Finally, FIFO PCI bus mastering is monitored/con-
trolled though this register.
Location 45h Configuration Bits
Bit 7
Bus Master Register Access
0
Address and transfer count registers only accessi-
ble from the Add-On interface
1
Address and transfer count registers only accessi-
ble from the PCI interface (default)
Bit 6
RDFIFO#, RD# Operation
0
Enable - RDFIFO# and RD# functions.
1
Not allowed. Must be 0.
Bit 5
WRFIFO#, WR# Operation
0
Enable - WRFIFO# and WR# functions.
1
Not allowed. Must be 0.
Bit 0
Target Latency Timer Enable
0
Disable PCI Latency Timer Time Out - Will not dis-
connect with retry if cannot issue TRDY in speci-
fied time
1
Enable PCI Latency Timer Time Out - Will be PCI
2.1 compliant
相關PDF資料 |
PDF描述 |
|---|---|
| S5935QRC | PCI Product |
| S5935TFC | PCI Product |
| S5935TF | PCI 5V Bus Master/Target Device 32-bit |
| S5935 | PCI 5V Bus Master/Target Device 32-bit |
| S5935QF | PCI 5V Bus Master/Target Device 32-bit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S59355QRC | 制造商:AppliedMicro 功能描述: |
| S5935QF | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:PCI Product |
| S5935QRC | 制造商:AppliedMicro 功能描述:PCI Master Device 160-Pin PQFP |
| S5935TF | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:PCI 5V Bus Master/Target Device 32-bit |
| S5935TFC | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:PCI Product |
發布緊急采購，3分鐘左右您將得到回復。