- 您現在的位置：買賣IC網 > PDF目錄374665 > S3035 (Applied Micro Circuits Corp.) SONET/SDH/ATM OC-3/12 Transceiver W/CDR(頻率可選，帶片上高頻鎖相環的SONET/SDH收發器（完全集成OC-3/12接口器件）) PDF資料下載
參數資料
| 型號： | S3035 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | SONET/SDH/ATM OC-3/12 Transceiver W/CDR(頻率可選，帶片上高頻鎖相環的SONET/SDH收發器（完全集成OC-3/12接口器件）) |
| 中文描述： | 的SONET / SDH / ATM的OC-3/12收發瓦/的CDR（頻率可選，帶片上高頻鎖相環的的SONET / SDH收發器（完全集成OC-3/12接口器件）） |
| 文件頁數： | 8/22頁 |
| 文件大?。?/td> | 151K |
| 代理商： | S3035 |
8
S3035
SONET/SDH/ATM OC-3/12 TRANSCEIVER W/CDR
July 25, 2000 / Revision E
OTHER OPERATING MODES
Diagnostic Loopback
When the Diagnostic Loopback Enable (DLEB) input
is active, a loopback from the transmitter to the re-
ceiver at the serial data rate can be set up for
diagnostic purposes. SDPECL must be High for di-
agnostic loopback.
The differential serial output data from the transmitter
is routed to the clock recovery unit and serial-to-par-
allel block in place of the normal Receive Data
Stream (RSD).
Line Loopback
When Line Loopback Enable (LLEB) is active, a
loopback from the receiver to the transmitter at the
serial data rate can be set up for facility loopback
testing. The recovered clock is used to retime the
incoming data before driving the TSDP/N outputs. In
line loopback mode, the TSCLKP/N outputs will be
driven by the receiver recovered clock.
Serial Loop Timing
In Serial Loop Timing mode (SLPTIME), the clock
synthesizer PLL of the S3035 is bypassed, and the
timing of the entire transmitter section is controlled
by the recovered receive serial clock. This mode is
entered by using the SLPTIME input.
In this mode the REFCLKP/N input is not used, and
the MODE[1:0] inputs are ignored for all transmit
functions. It should be carefully noted that the inter-
nal PLL continues to operate in this mode, and
continues as the source for the 38.51 MHZCLK, and
if this signal is being used, the REFCLKP/N and
MODE[1:0] inputs must be properly driven.
Forward Clocking
For both 77.78 MHz and 38.88 MHz reference op-
eration, the S3035 operates in the forward clocking
mode. The PLL locks the PCLK output of the trans-
mitter section to the REFCLK with a fixed and
repeatable phase relation. This allows the transmit-
ter data source to also be the timing source for the
serial clock synthesis.
The rising edge of PCLK is locked to the rising edge
of REFCLKP, with a maximum delay of 8 to 10 nsec
due to the PCLK TTL output driver.
For operation at 19.44 MHz and 51.84 MHz refer-
ences, separate timing paths are used for PLL
control and PCLK generation, and forward clocking
is not recommended.
Looptime Mode
When Serial Looptime Enable (SLPTIME) is active,
the serial recovered clock from the receiver will re-
place the serial clock in the transmitter section.
相關PDF資料 |
PDF描述 |
|---|---|
| S3037 | SONET/SDH/ATM OC-3/12 Transceiver W/CDR(19.44和77.76 MHz兩種頻率可選的SONET/SDH收發器) |
| S3038 | SONET/SDH/ATM OC-12 Quad Transceiver(SONET/SDH四收發器（完全集成OC-12接口器件）) |
| S3040A | SONET/SDH Clock Recovery Unit(帶片上高頻鎖相環的SONET/SDH時鐘恢復單元) |
| S3040B | SONET/SDH Clock Recovery Unit(帶片上高頻鎖相環的SONET/SDH時鐘恢復單元) |
| S3040 | OC-48 Clock Recovery Unit(OC-48時鐘恢復單元) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S3038TB | 制造商:AppliedMicro 功能描述: |
| S30395-1-G | 制造商: 功能描述: 制造商:undefined 功能描述: |
| S30395-513G | 制造商: 功能描述: 制造商:undefined 功能描述: |
| S303AB | 制造商:Cinch Connectors 功能描述:Conn Wire to Board SKT 3 POS Solder Lug ST Panel Mount |
| S-303-AB | 功能描述:Jones 插頭和插槽 3C PNL MNT SOCKET RoHS:否 制造商:Molex 產品類型:Socket Connectors 系列:Beau 位置/觸點數量:8 電壓額定值:250 V 電流額定值:10 A 外殼材料:Thermoplastic 觸點材料:Phosphor Bronze 觸點電鍍:Tin-Lead |
發布緊急采購，3分鐘左右您將得到回復。