參數資料
型號： R5F64211JFB
元件分類： 微控制器/微處理器
英文描述： 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 34/50頁
文件大?。?/td> 777K
代理商： R5F64211JFB
112
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
Figure 16-8. Phase Correct PWM Mode, timing diagram.
The Timer/Counter Overflow Flag (TOV1) is set each time the counter reaches BOTTOM. When either OCR1A or
ICR1 is used for defining the TOP value, the OC1A or ICF1 Flag is set accordingly at the same timer clock cycle as
the OCR1x Registers are updated with the double buffer value (at TOP). The Interrupt Flags can be used to gener-
ate an interrupt each time the counter reaches the TOP or BOTTOM value.
When changing the TOP value the program must ensure that the new TOP value is higher or equal to the value of
all of the Compare Registers. If the TOP value is lower than any of the Compare Registers, a compare match will
never occur between the TCNT1 and the OCR1x. Note that when using fixed TOP values, the unused bits are
masked to zero when any of the OCR1x Registers are written. As the third period shown in Figure 16-8 illustrates,
changing the TOP actively while the Timer/Counter is running in the phase correct mode can result in an unsym-
metrical output. The reason for this can be found in the time of update of the OCR1x Register. Since the OCR1x
update occurs at TOP, the PWM period starts and ends at TOP. This implies that the length of the falling slope is
determined by the previous TOP value, while the length of the rising slope is determined by the new TOP value.
When these two values differ the two slopes of the period will differ in length. The difference in length gives the
unsymmetrical result on the output.
It is recommended to use the phase and frequency correct mode instead of the phase correct mode when chang-
ing the TOP value while the Timer/Counter is running. When using a static TOP value there are practically no
differences between the two modes of operation.
In phase correct PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins. Setting
the COM1x1:0 bits to two will produce a non-inverted PWM and an inverted PWM output can be generated by set-
ting the COM1x1:0 to three (See Table 16-4 on page 118). The actual OC1x value will only be visible on the port
pin if the data direction for the port pin is set as output (DDR_OC1x). The PWM waveform is generated by setting
(or clearing) the OC1x Register at the compare match between OCR1x and TCNT1 when the counter increments,
and clearing (or setting) the OC1x Register at compare match between OCR1x and TCNT1 when the counter dec-
rements. The PWM frequency for the output when using phase correct PWM can be calculated by the following
equation:
The N variable represents the prescaler divider (1, 8, 64, 256 or 1024).
The extreme values for the OCR1x Register represent special cases when generating a PWM waveform output in
the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the output will be continuously low and if set
OCRnx/TOP Update and
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
1
2
3
4
TOVn Interrupt Flag Set
(Interrupt on Bottom)
TCNTn
Period
OCnx
(COMnx1:0 = 2)
(COMnx1:0 = 3)
f
OCnxPCPWM
f
clk_I/O
2 NTOP
----------------------------
=
相關PDF資料
PDF描述
R5F64211KFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F6421FJFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F6421GJFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F6421HKFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F64212KFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
R5F64211KFB 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F64211LFB 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F64212JFB 制造商:Renesas Electronics Corporation 功能描述:
R5F64212KFB 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F64212LFB 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*