- 您現在的位置：買賣IC網 > PDF目錄365370 > PM75RSK060 (POWEREX INC) Intellimod⑩ Module Three Phase Brake IGBT Inverter Output (75 Amperes/600 Volts) PDF資料下載
參數資料
| 型號： | PM75RSK060 |
| 廠商： | POWEREX INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Intellimod⑩ Module Three Phase Brake IGBT Inverter Output (75 Amperes/600 Volts) |
| 中文描述： | AC MOTOR CONTROLLER, 150 A, DMA25 |
| 封裝： | POWER MODULE-25 |
| 文件頁數： | 29/31頁 |
| 文件大小： | 925K |
| 代理商： | PM75RSK060 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁
Sep.1998
6.6.5 Dead Time (t
dead
)
In order to prevent arm shoot
through a dead time between high
and low side input ON signals is
required to be included in the sys-
tem control logic. Two different val-
ues are specified on the datasheet:
A. t
dead
measured directly on
the IPM input terminals
B. t
dead
related to optocoupler
input signals using the
recommended application
circuit
The specified type B dead time is
related to standard high speed
optocouplers. (See Section 6.6.2)
By using specially selected
optocouplers with narrow distribu-
tion of switching times
the required type B dead time
could be reduced.
6.6.6 Using the Fault Signal
In order to keep the interface cir-
cuits simple the IPM uses
a single on/off output to alert the
system controller of all fault condi-
tions. The system controller can
easily determine whether the fault
signal was caused by an over tem-
perature or over current/short cir-
cuit by examining its duration.
Short circuit and over current con-
dition fault signals will be t
FO
(nominal 1.5ms) in duration. An
over temperature fault signal will be
much longer. The over temperature
Figure 6.45
PCB Layout for V-Series Connector
fault starts when the base plate
temperature exceeds the OT level
and does not reset until the base
plate cools below the OT
r
level.
Typically this takes tens of sec-
onds.
Note:
Unused fault outputs must be prop-
erly terminated by connecting them
to the +15V on the local control
power supply. Failure to properly
terminate unused fault outputs may
result in unexpected tripping of the
modules internal protection.
3 ± 0.05
3 ± 0.05
3 ± 0.05
3 ± 0.05
3 ± 0.05
43.57 ± 0.1
19 - 1.2
+0
19 - 0.9
+0
4 - 3.2
+0.1
14.1 ± 0.05
14.1 ± 0.05
2.54 ± 0.05
2.54 ± 0.05
14.1 ± 0.05
14.6 ± 0.1
Table 6.8 V-Series IPM Connection Methods
V-Series Intelligent Power Module Type
Connection Method
PM75RVA060, PM100CVA060, PM150CVA060,
PM200CVA060, PM300CVA060, PM50RVA120,
PM75CVA120, PM100CVA120, PM150CVA120
19 Position, 0.1" Compound
Inverse Header Receptacle,
Hirose Part # MDF92-19S-2.54DSA
PM400DVA060, PM600DVA060,
PM200DVA120, PM300DVA120
5 Position, 0.1" (2.54mm)
Inverse Header Receptacle,
Hirose Part # MDF7-5S-2.54DSA
MITSUBISHI SEMICONDUCTORS POWER MODULES MOS
USING INTELLIGENT POWER MODULES
相關PDF資料 |
PDF描述 |
|---|---|
| PM800HSA060 | CAP,CERAMIC,47NF ,X7R,10%,50V,0805,SMD |
| PM800HSA120 | FLAT-BASE TYPE INSULATED PACKAGE |
| PN2222 | General Purpose Transistors NPN Silicon(NPN通用晶體管) |
| PN2222A | General Purpose Transistors NPN Silicon(NPN通用晶體管) |
| PN2907ARLRA | General Purpose Transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PM75RVA060 | 功能描述:MOD IPM HF 600V 75A RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
| PM75RVA060_05 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:FLAT-BASE TYPE INSULATED PACKAGE |
| PM75RVA060_11 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:FLAT-BASE TYPE INSULATED PACKAGE |
| PM75-XXXK | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SMT POWER INDUCTORS |
| PM761 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。