參數資料
型號： PM75RSK060
廠商： Mitsubishi Electric Corporation
英文描述： 470UF 20% 35V RAD
中文描述： 用智能功率模塊
文件頁數： 29/31頁
文件大?。?/td> 925K
代理商： PM75RSK060
Sep.1998
6.6.5 Dead Time (t
dead
)
In order to prevent arm shoot
through a dead time between high
and low side input ON signals is
required to be included in the sys-
tem control logic. Two different val-
ues are specified on the datasheet:
A. t
dead
measured directly on
the IPM input terminals
B. t
dead
related to optocoupler
input signals using the
recommended application
circuit
The specified type B dead time is
related to standard high speed
optocouplers. (See Section 6.6.2)
By using specially selected
optocouplers with narrow distribu-
tion of switching times
the required type B dead time
could be reduced.
6.6.6 Using the Fault Signal
In order to keep the interface cir-
cuits simple the IPM uses
a single on/off output to alert the
system controller of all fault condi-
tions. The system controller can
easily determine whether the fault
signal was caused by an over tem-
perature or over current/short cir-
cuit by examining its duration.
Short circuit and over current con-
dition fault signals will be t
FO
(nominal 1.5ms) in duration. An
over temperature fault signal will be
much longer. The over temperature
Figure 6.45
PCB Layout for V-Series Connector
fault starts when the base plate
temperature exceeds the OT level
and does not reset until the base
plate cools below the OT
r
level.
Typically this takes tens of sec-
onds.
Note:
Unused fault outputs must be prop-
erly terminated by connecting them
to the +15V on the local control
power supply. Failure to properly
terminate unused fault outputs may
result in unexpected tripping of the
modules internal protection.
3 ± 0.05
3 ± 0.05
3 ± 0.05
3 ± 0.05
3 ± 0.05
43.57 ± 0.1
19 - 1.2
+0
19 - 0.9
+0
4 - 3.2
+0.1
14.1 ± 0.05
14.1 ± 0.05
2.54 ± 0.05
2.54 ± 0.05
14.1 ± 0.05
14.6 ± 0.1
Table 6.8 V-Series IPM Connection Methods
V-Series Intelligent Power Module Type
Connection Method
PM75RVA060, PM100CVA060, PM150CVA060,
PM200CVA060, PM300CVA060, PM50RVA120,
PM75CVA120, PM100CVA120, PM150CVA120
19 Position, 0.1" Compound
Inverse Header Receptacle,
Hirose Part # MDF92-19S-2.54DSA
PM400DVA060, PM600DVA060,
PM200DVA120, PM300DVA120
5 Position, 0.1" (2.54mm)
Inverse Header Receptacle,
Hirose Part # MDF7-5S-2.54DSA
MITSUBISHI SEMICONDUCTORS POWER MODULES MOS
USING INTELLIGENT POWER MODULES
相關PDF資料
PDF描述
PM75RSK060 Intellimod⑩ Module Three Phase Brake IGBT Inverter Output (75 Amperes/600 Volts)
PM800HSA060 CAP,CERAMIC,47NF ,X7R,10%,50V,0805,SMD
PM800HSA120 FLAT-BASE TYPE INSULATED PACKAGE
PN2222 General Purpose Transistors NPN Silicon(NPN通用晶體管)
PN2222A General Purpose Transistors NPN Silicon(NPN通用晶體管)
相關代理商/技術參數
參數描述
PM75RVA060 功能描述:MOD IPM HF 600V 75A RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊
PM75RVA060_05 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:FLAT-BASE TYPE INSULATED PACKAGE
PM75RVA060_11 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:FLAT-BASE TYPE INSULATED PACKAGE
PM75-XXXK 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SMT POWER INDUCTORS
PM761 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*