- 您現在的位置：買賣IC網 > PDF目錄370003 > PIP250M Integrated buck converter PDF資料下載
參數資料
| 型號： | PIP250M |
| 英文描述： | Integrated buck converter |
| 中文描述： | 集成的降壓轉換器 |
| 文件頁數： | 4/19頁 |
| 文件大小： | 334K |
| 代理商： | PIP250M |
Philips Semiconductors
PIP250M
Integrated buck converter
Product data
Rev. 02 — 21 February 2003
4 of 19
9397 750 10904
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
[1]
[2]
PAD1, PAD2 and PAD3 are electrical connections and must be soldered to the printed circuit board
All n.c. pins should be connected to V
SSC
.
7.
Functional description
7.1 Pin functions
7.1.1
Output stage supply (V
DDO
, V
SSO
)
The power output stage of the PIP250M consists of two N-channel, power MOSFETs
and a Schottky diode configured as a synchronous buck converter. The drain of the
upper MOSFET is connected to the positive conversion supply (V
DDO
), and the
source of the lower MOSFET is connected to power ground (V
SSO
). The Schottky
diode is connected between the source and drain of the lower MOSFET.
7.1.2
Output voltage (VO)
VO is the switched node of the power MOSFET output stage. This node is connected
internally to the source of the upper MOSFET and the drain of the lower MOSFET.
7.1.3
Control circuit supply (V
DDC
, V
SSC
)
V
DDC
is the positive supply to the control circuit. V
SSC
is the control circuit ground. All
control voltages are measured with respect to V
SSC
.
7.1.4
Bootstrap capacitor connection (CB)
The upper MOSFET driver stage is powered from the CB pin.
7.1.5
Voltage feedback pin (FB)
The FB pin is connected to the inverting input of the error amplifier, and to the inputs
of the overvoltage and undervoltage comparators.
7.1.6
Current limit set and enable input (OCSET/ENABLE)
The overcurrent threshold is set by an external resistor between V
DDO
and
OCSET/ENABLE. The PIP250M can be shut down by pulling this pin LOW.
7.1.7
Sense connection for current limit (PHASE)
The PHASE input is normally connected externally to the power output stage
switched node (VO). The voltage on the PHASE input is compared with the voltage
on the OCSET/ENABLE input during the interval when the upper MOSFET is on. The
overcurrent trip operates if the voltage on the PHASE input is lower than the voltage
on the OCSET/ENABLE input.
相關PDF資料 |
PDF描述 |
|---|---|
| PIP3103-T | TRANSISTOR | MOSFET | N-CHANNEL | SOT-223 |
| PIP3106-D | TRANSISTOR | MOSFET | N-CHANNEL | 50V V(BR)DSS | TO-252AA |
| PIP3107-D | TRANSISTOR | MOSFET | N-CHANNEL | 50V V(BR)DSS | TO-252AA |
| PIP3104 | PowerMOS transistor Logic level TOPFET |
| PIP3104-P | PowerMOS transistor Logic level TOPFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIP250M,518 | 功能描述:IC REG BUCK SYNC ADJ 15A 68HVQFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| PIP26U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Fibers can be free cut using fiber cutter |
| PIP30 | 制造商:Microsemi Corporation 功能描述:TVS SGL BI-DIR 42.5V 7.5KW 2PIN CASE 11 - Bulk 制造商:ProTek Devices 功能描述:Suppressor Assembly 30V 7.5KW |
| PIP3101-A,127 | 功能描述:MOSFET RAIL TOPFET2 RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| PIP3102-R | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LOGIC LEVEL TOPFET |
發布緊急采購，3分鐘左右您將得到回復。