- 您現在的位置：買賣IC網 > PDF目錄368030 > PIC876 (Microchip Technology Inc.) 28/40-pin 8-Bit CMOS FLASH Microcontrollers PDF資料下載
參數資料
| 型號： | PIC876 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 28/40-pin 8-Bit CMOS FLASH Microcontrollers |
| 中文描述： | 28/40-pin 8位CMOS閃存微控制器 |
| 文件頁數： | 81/200頁 |
| 文件大?。?/td> | 3544K |
| 代理商： | PIC876 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁
PIC16F87X
1999 Microchip Technology Inc.
DS30292A-page 81
9.2.11
I
2
C MASTER MODE TRANSMISSION
Transmission of a data byte, a 7-bit address or either
half of a 10-bit address is accomplished by simply writ-
ing a value to SSPBUF register. This action will set the
buffer full flag (BF) and allow the baud rate generator to
begin counting and start the next transmission. Each
bit of address/data will be shifted out onto the SDA pin
after the falling edge of SCL is asserted (see data hold
time spec). SCL is held low for one baud rate gener-
ator rollover count (T
BRG
). Data should be valid before
SCL is released high (see data setup time spec).
When the SCL pin is released high, it is held that way
for T
BRG
. The data on the SDA pin must remain stable
for that duration and some hold time after the next fall-
ing edge of SCL. After the eighth bit is shifted out (the
falling edge of the eighth clock), the BF flag is cleared
and the master releases SDA allowing the slave device
being addressed to respond with an ACK bit during the
ninth bit time, if an address match occurs or if data was
received properly. The status of ACK is read into the
ACKDT on the falling edge of the ninth clock. If the
master receives an acknowledge, the acknowledge
status bit (ACKSTAT) is cleared. If not, the bit is set.
After the ninth clock, the SSPIF is set and the master
clock (baud rate generator) is suspended until the next
data byte is loaded into the SSPBUF, leaving SCL low
and SDA unchanged (
Figure 9-14
).
After the write to the SSPBUF, each bit of address will
be shifted out on the falling edge of SCL until all seven
address bits and the R/W bit are completed. On the fall-
ing edge of the eighth clock, the master will de-assert
the SDA pin allowing the slave to respond with an
acknowledge. On the falling edge of the ninth clock, the
master will sample the SDA pin to see if the address
was recognized by a slave. The status of the ACK bit is
loaded into the ACKSTAT status bit (SSPCON2<6>).
Following the falling edge of the ninth clock transmis-
sion of the address, the SSPIF is set, the BF flag is
cleared, and the baud rate generator is turned off until
another write to the SSPBUF takes place, holding SCL
low and allowing SDA to float.
9.2.11.1
BF STATUS FLAG
In transmit mode, the BF bit (SSPSTAT<0>) is set when
the CPU writes to SSPBUF and is cleared when all 8
bits are shifted out.
9.2.11.2
WCOL STATUS FLAG
If the user writes the SSPBUF when a transmit is
already in progress (i.e. SSPSR is still shifting out a
data byte), then WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
WCOL must be cleared in software.
9.2.11.3
ACKSTAT STATUS FLAG
In transmit mode, the ACKSTAT bit (SSPCON2<6>) is
cleared when the slave has sent an acknowledge
(ACK = 0), and is set when the slave does not acknowl-
edge (ACK = 1). A slave sends an acknowledge when
it has recognized its address (including a general call),
or when the slave has properly received its data.
相關PDF資料 |
PDF描述 |
|---|---|
| PIP201-12M-3 | DC-to-DC converter powertrain |
| PIP3102-R | LOGIC LEVEL TOPFET |
| PIP3203-A | TOPFET high side switch |
| PIP3206-R | TOPFET high side switch SMD version |
| PIP8.4 | 7,500 & 15,000 Watt TVS Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC9310 | 制造商:PICSEMI 制造商全稱:PICSEMI 功能描述:Async Boost with 600KHz switching |
| PICADILLO-35T | 功能描述:Resistive Graphic LCD Display Module Transmissive Red, Green, Blue (RGB) TFT - Color I2C, SPI 3.5" (88.90mm) 320 x 480 制造商:4d systems pty ltd 系列:- 零件狀態:有效 顯示類型:TFT - 彩色 顯示模式:可傳導的 觸摸屏:電阻 屏幕對角線尺寸:3.5"（88.90mm） 可視范圍:73.40mm 寬 x 49.00mm 高 背光:LED - 白 點像素:320 x 480 接口:I2C，SPI 圖形顏色:紅，綠，藍（RGB） 背景顏色:- 點尺寸:- 點間距:0.15mm 寬 x 0.15mm 高 標準包裝:1 |
| PICADLL | 制造商:CALIBRE UK 功能描述:DEVELOPMENT DLLS I2C ADAPTER |
| PICAMBOX | 制造商:Nwazet 功能描述:PI CAMERA BOX |
| PICAMBOXBUNDLE | 制造商:Nwazet 功能描述:PI CAMERA BOX BUNDLE WITH FISHEYE LENS |
發布緊急采購，3分鐘左右您將得到回復。