- 您現在的位置：買賣IC網 > PDF目錄368030 > PIC876 (Microchip Technology Inc.) 28/40-pin 8-Bit CMOS FLASH Microcontrollers PDF資料下載
參數資料
| 型號： | PIC876 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 28/40-pin 8-Bit CMOS FLASH Microcontrollers |
| 中文描述： | 28/40-pin 8位CMOS閃存微控制器 |
| 文件頁數： | 53/200頁 |
| 文件大?。?/td> | 3544K |
| 代理商： | PIC876 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁
1999 Microchip Technology Inc.
DS30292B-page 53
PIC16F87X
6.4
Timer1 Operation in Asynchronous
Counter Mode
If control bit T1SYNC (T1CON<2>) is set, the external
clock input is not synchronized. The timer continues to
increment asynchronous to the internal phase clocks.
The timer will continue to run during SLEEP and can
generate an interrupt on overflow, which will wake-up
the processor. However, special precautions in soft-
ware are needed to read/write the timer (Section 6.4.1).
In asynchronous counter mode, Timer1 can not be used
as a time-base for capture or compare operations.
6.4.1
READING AND WRITING TIMER1 IN
ASYNCHRONOUS COUNTER MODE
Reading TMR1H or TMR1L while the timer is running
from an external asynchronous clock will guarantee a
valid read (taken care of in hardware). However, the
user should keep in mind that reading the 16-bit timer
in two 8-bit values itself poses certain problems, since
the timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write conten-
tion may occur by writing to the timer registers, while
the register is incrementing. This may produce an
unpredictable value in the timer register.
Reading the 16-bit value requires some care. Examples
12-2 and 12-3 in the PICmicro
Mid-Range MCU Fam-
ily Reference Manual (DS33023) show how to read and
write Timer1 when it is running in asynchronous mode.
6.5
Timer1 Oscillator
A crystal oscillator circuit is built-in between pins T1OSI
(input) and T1OSO (amplifier output). It is enabled by
setting control bit T1OSCEN (T1CON<3>). The oscilla-
tor is a low power oscillator rated up to 200 kHz. It will
continue to run during SLEEP. It is primarily intended
for use with a 32 kHz crystal. Table 6-1 shows the
capacitor selection for the Timer1 oscillator.
The Timer1 oscillator is identical to the LP oscillator.
The user must provide a software time delay to ensure
proper oscillator start-up.
TABLE 6-1:
CAPACITOR SELECTION FOR
THE TIMER1 OSCILLATOR
6.6
Resetting Timer1 using a CCP Trigger
Output
If the CCP1 or CCP2 module is configured in compare
mode
to
generate
a
(CCP1M3:CCP1M0 =
1011
), this signal will reset
Timer1.
“special
event
trigger”
Timer1 must be configured for either timer or synchro-
nized counter mode to take advantage of this feature. If
Timer1 is running in asynchronous counter mode, this
reset operation may not work.
In the event that a write to Timer1 coincides with a spe-
cial event trigger from CCP1 or CCP2, the write will
take precedence.
In this mode of operation, the CCPRxH:CCPRxL regis-
ter pair effectively becomes the period register for
Timer1.
6.7
Resetting of Timer1 Register Pair
(TMR1H, TMR1L)
TMR1H and TMR1L registers are not reset to 00h on a
POR or any other reset except by the CCP1 and CCP2
special event triggers.
T1CON register is reset to 00h on a Power-on Reset or
a Brown-out Reset, which shuts off the timer and
leaves a 1:1 prescale. In all other resets, the register is
unaffected.
6.8
Timer1 Prescaler
The prescaler counter is cleared on writes to the
TMR1H or TMR1L registers.
Osc Type
LP
Freq
32 kHz
100 kHz
200 kHz
C1
33 pF
15 pF
15 pF
C2
33 pF
15 pF
15 pF
These values are for design guidance only.
Crystals Tested:
32.768 kHz
Epson C-001R32.768K-A
100 kHz
Epson C-2 100.00 KC-P
200 kHz
STD XTL 200.000 kHz
Note 1:
Higher capacitance increases the stability of
oscillator but also increases the start-up time.
2:
Since each resonator/crystal has its own charac-
teristics, the user should consult the resonator/
crystal manufacturer for appropriate values of
external components.
±
20 PPM
±
20 PPM
±
20 PPM
Note:
The special event triggers from the CCP1
and CCP2 modules will not set interrupt
flag bit TMR1IF (PIR1<0>).
相關PDF資料 |
PDF描述 |
|---|---|
| PIP201-12M-3 | DC-to-DC converter powertrain |
| PIP3102-R | LOGIC LEVEL TOPFET |
| PIP3203-A | TOPFET high side switch |
| PIP3206-R | TOPFET high side switch SMD version |
| PIP8.4 | 7,500 & 15,000 Watt TVS Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC9310 | 制造商:PICSEMI 制造商全稱:PICSEMI 功能描述:Async Boost with 600KHz switching |
| PICADILLO-35T | 功能描述:Resistive Graphic LCD Display Module Transmissive Red, Green, Blue (RGB) TFT - Color I2C, SPI 3.5" (88.90mm) 320 x 480 制造商:4d systems pty ltd 系列:- 零件狀態:有效 顯示類型:TFT - 彩色 顯示模式:可傳導的 觸摸屏:電阻 屏幕對角線尺寸:3.5"（88.90mm） 可視范圍:73.40mm 寬 x 49.00mm 高 背光:LED - 白 點像素:320 x 480 接口:I2C，SPI 圖形顏色:紅，綠，藍（RGB） 背景顏色:- 點尺寸:- 點間距:0.15mm 寬 x 0.15mm 高 標準包裝:1 |
| PICADLL | 制造商:CALIBRE UK 功能描述:DEVELOPMENT DLLS I2C ADAPTER |
| PICAMBOX | 制造商:Nwazet 功能描述:PI CAMERA BOX |
| PICAMBOXBUNDLE | 制造商:Nwazet 功能描述:PI CAMERA BOX BUNDLE WITH FISHEYE LENS |
發布緊急采購，3分鐘左右您將得到回復。