參數資料
型號： PIC18F46J50-I/PT
廠商： Microchip Technology
文件頁數： 45/164頁
文件大?。?/td> 0K
描述： IC PIC MCU FLASH 64KB 44-TQFP
產品培訓模塊： XLP Deep Sleep Mode
PIC18 J Series MCU Overview
PIC18F MPLAB® Starter Kit
8-bit PIC® Microcontroller Portfolio
標準包裝： 160
系列： PIC® XLP™ 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 48MHz
連通性： I²C，SPI，UART/USART，USB
外圍設備： 欠壓檢測/復位，DMA，POR，PWM，WDT
輸入/輸出數： 34
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 3.8K x 8
電壓 - 電源 (Vcc/Vdd)： 2.15 V ~ 3.6 V
數據轉換器： A/D 13x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-TQFP
包裝： 托盤
產品目錄頁面： 657 (CN2011-ZH PDF)
配用： AC164330-ND - MODULE SKT FOR 44TQFP 18F45J10
2011 Microchip Technology Inc.
DS39931D-page 139
PIC18F46J50 FAMILY
10.3
PORTB, TRISB and LATB
Registers
PORTB is an 8-bit wide, bidirectional port. The corre-
sponding Data Direction register is TRISB. Setting a
TRISB bit (= 1) will make the corresponding PORTB
pin an input (i.e., put the corresponding output driver in
a High-Impedance mode). Clearing a TRISB bit (= 0)
will make the corresponding PORTB pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Data Latch register (LATB) is also memory
mapped. Read-modify-write operations on the LATB
register read and write the latched output value for
PORTB.
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is
performed by clearing bit, RBPU (INTCON2<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on a POR. The integrated weak pull-ups
consist of a semiconductor structure similar to, but
somewhat different, from a discrete resistor. On an
unloaded I/O pin, the weak pull-ups are intended to
provide logic high indication, but will not necessarily
pull the pin all the way to VDD levels.
Four of the PORTB pins (RB<7:4>) have an interrupt-
on-change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB<7:4> pin
configured as an output is excluded from the interrupt-
on-change comparison). The input pins (of RB<7:4>)
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of RB<7:4>
are ORed together to generate the RB Port Change
Interrupt with Flag bit, RBIF (INTCON<0>).
This interrupt can wake the device from Sleep mode or
any of the Idle modes. Application software can clear
the interrupt flag by following these steps:
1.
Any read or write of PORTB (except with the
MOVFF (ANY), PORTB
instruction).
2.
Wait one instruction cycle (such as executing a
NOP
instruction).
3.
Clear flag bit, RBIF.
A mismatch condition continues to set flag bit, RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit, RBIF, to be cleared after one instruction
cycle of delay.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
The RB5 pin is multiplexed with the Timer0 module
clock input and one of the comparator outputs to
become the RB5/PMA0/KBI1/SDI1/SDA1/RP8 pin.
EXAMPLE 10-3:
INITIALIZING PORTB
Note:
On a POR, the RB<3:0> bits are
configured as analog inputs by default and
read as ‘0’; RB<7:4> bits are configured
as digital inputs.
MOVLW
0x08
; Initialize output data
MOVWF
LATB
; latch values for digital
; output pins.
MOVLB
0x0F
; ANCONx registers are
; not in access bank
BSF
ANCON1, PCFG12, BANKED
; Configure RB0/AN12 for digital input mode
BCF
ANCON1, PCFG10, BANKED
; Configure RB1/AN10 for analog input mode
MOVLW
0xC3
; RB0 configured as digital input
MOVWF
TRISB
; RB1 configured as analog input
; RB2 configured as output low
; RB3 configured as output high
; RB4 configured as output low
; RB5 configured as output low
; RB6 configured as digital input
; RB7 configured as digital input
相關PDF資料
PDF描述
PIC18F46K20-E/P IC PIC MCU FLASH 32KX16 40-DIP
PIC18F46K20-I/MV MCU PIC 64KB FLASH 40QFN
PIC18F47J53-I/ML IC PIC MCU 128KB FLASH 44QFN
PIC18F65K90-I/MR IC MCU 8BIT 32KB FLASH 64QFN
PIC18F66K80-I/MR MCU PIC 64KB FLASH 64QFN
相關代理商/技術參數
參數描述
PIC18F46J50T-I/ML 功能描述:8位微控制器 -MCU Full Spd USB 64KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J50T-I/PT 功能描述:8位微控制器 -MCU Full Spd USB 64KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J53-I/ML 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J53-I/PT 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J53T-I/ML 功能描述:8位微控制器 -MCU USB 64KB Flash 4KB RAM 12 MIPS 12b ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*