參數資料
型號: PIC16LF84A
廠商: Microchip Technology Inc.
英文描述: 18-pin Enhanced Flash/EEPROM 8-Bit Microcontroller
中文描述: 18引腳增強型閃存/ EEPROM的8位微控制器
文件頁數: 32/68頁
文件大?。?/td> 494K
代理商: PIC16LF84A
PIC16F84A
DS35007A-page 32
Preliminary
1998 Microchip Technology Inc.
6.11.3
WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
If the interrupt occurs
before
the execution of a
SLEEP
instruction, the
SLEEP
instruction will com-
plete as a NOP. Therefore, the WDT and WDT
postscaler will not be cleared, the TO bit will not
be set and PD bits will not be cleared.
If the interrupt occurs
during or after
the execu-
tion of a
SLEEP
instruction, the device will imme-
diately wake up from sleep. The
SLEEP
instruction
will be completely executed before the wake-up.
Therefore, the WDT and WDT postscaler will be
cleared, the TO bit will be set and the PD bit will
be cleared.
Even if the flag bits were checked before executing a
SLEEP
instruction, it may be possible for flag bits to
become set before the
SLEEP
instruction completes. To
determine whether a
SLEEP
instruction executed, test
the PD bit. If the PD bit is set, the
SLEEP
instruction
was executed as a NOP.
To ensure that the WDT is cleared, a
CLRWDT
instruc-
tion should be executed before a
SLEEP
instruction.
6.12
Program Verification/Code Protection
If the code protection bit(s) have not been
programmed, the on-chip program memory can be
read out for verification purposes.
6.13
ID Locations
Four memory locations (2000h - 2004h) are designated
as ID locations to store checksum or other code
identification numbers. These locations are not
accessible during normal execution but are readable
and writable only during program/verify. Only the
four least significant bits of ID location are usable.
6.14
In-Circuit Serial Programming
PIC16F84A
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. Customers can manufacture boards with
unprogrammed devices, and then program the
microcontroller just before shipping the product,
allowing the most recent firmware or custom firmware
to be programmed.
For complete details of serial programming, please
refer to the In-Circuit Serial Programming (ICSP)
Guide, (DS30277).
microcontrollers
can
be
serially
Note:
Microchip does not recommend code pro-
tecting windowed devices.
相關PDF資料
PDF描述
PIC17C42 High-Performance 8-Bit CMOS EPROM/ROM Microcontroller(每個I/O口有20mA吸收,35mA驅動,2K 位EPROM微控制器)
pic17cr43 High-Performance 8-Bit CMOS EPROM/ROM Microcontroller(每個I/O口有20mA吸收,35mA驅動,4K位EPROM)
PIC17C42A High-Performance 8-Bit CMOS EPROM/ROM Microcontroller(每個I/O口有20mA吸收,35mA驅動,2K位EPROM微控制器)
PIC17C43 High-Performance 8-Bit CMOS EPROM/ROM Microcontroller(每個I/O口有20mA吸收,35mA驅動,4K位EPROM微控制器)
PIC17C44 High-Performance 8-Bit CMOS EPROM/ROM Microcontroller(每個I/O口有20mA吸收,35mA驅動,8K位EPROM微控制器)
相關代理商/技術參數
參數描述
PIC16LF84A-04/P 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF84A-04/P 制造商:Microchip Technology Inc 功能描述:8-Bit Microcontroller IC
PIC16LF84A-04/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT FLASH MCU 制造商:Microchip Technology Inc 功能描述:IC, 8BIT FLASH MCU
PIC16LF84A-04/SO 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF84A-04/SS 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT