參數資料
型號: PIC16LC716T
廠商: Microchip Technology Inc.
英文描述: 8-Bit CMOS Microcontrollers with A/D Converter and Capture/Compare/PWM
中文描述: 8位CMOS微控制器與A / D轉換器和捕捉/比較/ PWM
文件頁數: 19/108頁
文件大?。?/td> 1810K
代理商: PIC16LC716T
PIC16C712/716
1999 Microchip Technology Inc.
Preliminary
DS41106A-page 19
2.3
PCL and PCLATH
The program counter (PC) specifies the address of the
instruction to fetch for execution. The PC is 13 bits
wide. The low byte is called the PCL register. This reg-
ister is readable and writable. The high byte is called
the PCH register. This register contains the PC<12:8>
bits and is not directly readable or writable. All updates
to the PCH register go through the PCLATH register.
2.3.1
STACK
The stack allows a combination of up to 8 program calls
and interrupts to occur. The stack contains the return
address from this branch in program execution.
Midrange devices have an 8 level deep x 13-bit wide
hardware stack. The stack space is not part of either
program or data space and the stack pointer is not
readable or writable. The PC is PUSHed onto the stack
when a
CALL
instruction is executed or an interrupt
causes a branch. The stack is POPed in the event of a
RETURN, RETLW
or a
RETFIE
instruction execution.
PCLATH is not modified when the stack is PUSHed or
POPed.
After the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
2.4
Program Memory Paging
The
CALL
and
GOTO
instructions provide 11 bits of
address to allow branching within any 2K program
memory page. When doing a
CALL
or
GOTO
instruction,
the upper bit of the address is provided by
PCLATH<3>. When doing a
CALL
or
GOTO
instruction,
the user must ensure that the page select bit is pro-
grammed so that the desired program memory page is
addressed. If a return from a
CALL
instruction (or inter-
rupt) is executed, the entire 13-bit PC is pushed onto
the stack. Therefore, manipulation of the PCLATH<3>
bit is not required for the return instructions (which
POPs the address from the stack).
相關PDF資料
PDF描述
PIC16C712T 8-Bit CMOS Microcontrollers with A/D Converter and Capture/Compare/PWM
PIC16C716T 8-Bit CMOS Microcontrollers with A/D Converter and Capture/Compare/PWM
PIC16LC712T 8-Bit CMOS Microcontrollers with A/D Converter and Capture/Compare/PWM
PIC16LC72 28-Pin 8-Bit CMOS Microcontrollers(28腳8位CMOS微控制器)
PIC16C70 8-Bit CMOS Microcontrollers with A/D converter(每個I/O口有25mA驅動/吸收電流,微控制器)
相關代理商/技術參數
參數描述
PIC16LC716T-04/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LC716T-04/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LC716T-04I/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LC716T-04I/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LC717/P 功能描述:8位微控制器 -MCU 3.5KB 256 RAM 16 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT