- 您現在的位置：買賣IC網 > PDF目錄11720 > PI7C8154BNAE (Pericom)IC PCI-PCI BRIDGE ASYNC 304-PBGA PDF資料下載
參數資料
| 型號： | PI7C8154BNAE |
| 廠商： | Pericom |
| 文件頁數： | 4/114頁 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| 標準包裝： | 27 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 304-BBGA |
| 供應商設備封裝： | 304-PBGA（31x31） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
PI7C8154B
ASYNCHRONOUS 2-PORT
PCI-to-PCI BRIDGE
Advance Information
Page 101 of 114
JUNE 2008 REVISION 1.1
15.2.3
REPORTING PARITY ERRORS
For all address phases, if a parity error is detected, the error should be reported on the P_SERR#
signal by asserting P_SERR# for one cycle and then tri-stating two cycles after the bad address.
P_SERR# can only be asserted if bit 6 and 8 in the Command Register are both set to 1. For write
data phases, a parity error should be reported by asserting the P_PERR# signal two cycles after the
data phase and should remain asserted for one cycle when bit 6 in the Command register is set to a
1. The target reports any type of data parity errors during write cycles, while the master reports data
parity errors during read cycles.
Detection of an address parity error will cause the PCI-to-PCI Bridge target to not claim the bus
(P_DEVSEL# remains inactive) and the cycle will then terminate with a Master Abort. When the
bridge is acting as master, a data parity error during a read cycle results in the bridge master
initiating a Master Abort.
15.2.4
SECONDARY IDSEL MAPPING
When PI7C8154B detects a Type 1 configuration transaction for a device connected to
the secondary, it translates the Type 1 transaction to Type 0 transaction on the downstream
interface. Type 1 configuration format uses a 5-bit field at P_AD[15:11] as a device number. This
is translated to S_AD[31:16] by PI7C8154B.
16
IEEE 1149.1 COMPATIBLE JTAG CONTROLLER
An IEEE 1149.1 compatible Test Access Port (TAP) controller and associated TAP pins are
provided to support boundary scan in PI7C8154B for board-level continuity test and diagnostics.
The TAP pins assigned are TCK, TDI, TDO, TMS and TRST#. All digital input, output,
input/output pins are tested except TAP pins.
The IEEE 1149.1 Test Logic consists of a TAP controller, an instruction register, and
a group of test data registers including Bypass and Boundary Scan registers. The TAP controller is
a synchronous 16-state machine driven by the Test Clock (TCK) and the Test Mode Select (TMS)
pins. An independent power on reset circuit is provided to ensure the machine is in
TEST_LOGIC_RESET state at power-up. The JTAG signal lines are not active when the PCI
resource is operating PCI bus cycles.
PI7C8154B implements 3 basic instructions: BYPASS, SAMPLE/PRELOAD, and EXTEST.
16.1
BOUNDARY SCAN ARCHITECTURE
Boundary-scan test logic consists of a boundary-scan register and support logic. These are accessed
through a Test Access Port (TAP). The TAP provides a simple serial interface that allows all
processor signal pins to be driven and/or sampled, thereby providing direct control and monitoring
of processor pins at the system level.
This mode of operation is valuable for design debugging and fault diagnosis since it permits
examination of connections not normally accessible to the test system. The following subsections
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1025AARQ | IC MONITOR SYS/VOLT 5CH 16QSOP |
| ADUC832BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 31-10 | BNC FRONT MOUNT RECEPT |
| D38999/20JD97SN | CONN RCPT 12POS WALL MNT W/SCKT |
| ADUC848BSZ62-5 | IC FLASH MCU W/16BIT ADC 52MQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8154BNAE-80 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154BNAI | 制造商:Pericom Semiconductor Corporation 功能描述: |
| PI7C8154BNAIE | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154EVB | 功能描述:界面開發工具 64B/66MHz 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C8154NA-33 | 制造商:PERICOM 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。