- 您現在的位置：買賣IC網 > PDF目錄368020 > PI7C8154 PCI Bridge | 2-Port PCI-to-PCI Bridge PDF資料下載
參數資料
| 型號： | PI7C8154 |
| 英文描述： | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| 中文描述： | PCI橋| 2端口PCI至PCI橋 |
| 文件頁數： | 25/115頁 |
| 文件大小： | 879K |
| 代理商： | PI7C8154 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
PI7C8150B
2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 25 of 115
July 31, 2003 – Revision 1.031
Section 3.8.3.2 provides detailed information about how PI7C8150B responds to target
termination during posted write transactions.
3.5.2
MEMORY WRITE AND INVALIDATE
Posted write forwarding is used for Memory Write and Invalidate transactions.
If offset 74h bits [8:7] = 11, the PI7C8150B disconnects Memory Write and Invalidate
commands at aligned cache line boundaries. The cache line size value in the cache line size
register gives the number of DWORD in a cache line.
If offset 74h bits [8:7] = 00, the PI7C8150b converts Memory Write and Invalidate
transactions to Memory Write transactions at the destination.
If the value in the cache line size register does meet the memory write and invalidate
conditions, the PI7C8150B returns a target disconnect to the initiator on a cache line
boundary.
3.5.3
DELAYED WRITE TRANSACTIONS
Delayed write forwarding is used for I/O write transactions and Type 1 configuration write
transactions.
A delayed write transaction guarantees that the actual target response is returned back to
the initiator without holding the initiating bus in wait states. A delayed write transaction is
limited to a single DWORD data transfer.
When a write transaction is first detected on the initiator bus, and PI7C8150B forwards it
as a delayed transaction, PI7C8150B claims the access by asserting DEVSEL_L and
returns a target retry to the initiator. During the address phase, PI7C8150B samples the bus
command, address, and address parity one cycle later. After IRDY_L is asserted,
PI7C8150B also samples the first data DWORD, byte enable bits, and data parity. This
information is placed into the delayed transaction queue. The transaction is queued only if
no other existing delayed transactions have the same address and command, and if the
delayed transaction queue is not full. When the delayed write transaction moves to the head
of the delayed transaction queue and all ordering constraints with posted data are satisfied.
The PI7C8150B initiates the transaction on the target bus. PI7C8150B transfers the write
data to the target. If PI7C8150B receives a target retry in response to the write transaction
on the target bus, it continues to repeat the write transaction until the data transfer is
completed, or until an error condition is encountered.
If PI7C8150B is unable to deliver write data after 2
24
(default) or 2
32
(maximum) attempts,
PI7C8150B will report a system error. PI7C8150B also asserts P_SERR_L if the primary
SERR_L enable bit is set in the command register. See Section 6.4 for information on the
assertion of P_SERR_L. When the initiator repeats the same write transaction (same
command, address, byte enable bits, and data), and the completed delayed transaction is at
the head of the queue, the PI7C8150B claims the access by asserting DEVSEL_L and
returns TRDY_L to the initiator, to indicate that the write data was transferred. If the
initiator requests multiple DWORD, PI7C8150B also asserts STOP_L in conjunction with
TRDY_L to signal a target disconnect. Note that only those bytes of write data with valid
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8154-33 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150-33 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150A | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150A-33 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8154-33 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8154ANA | 功能描述:外圍驅動器與原件 - PCI 64-Bit/66MHz 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154ANAE | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154ANAE-33 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154B | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2 PORT 64 BIT 66MHZ PCI TO PCI BRIDGE |
發布緊急采購，3分鐘左右您將得到回復。