- 您現在的位置：買賣IC網 > PDF目錄368020 > PI7C8150B-33 PCI Bridge | Asynchronous 2-Port PCI Bridge PDF資料下載
參數資料
| 型號： | PI7C8150B-33 |
| 英文描述： | PCI Bridge | Asynchronous 2-Port PCI Bridge |
| 中文描述： | PCI橋|異步2端口PCI橋 |
| 文件頁數： | 102/115頁 |
| 文件大?。?/td> | 879K |
| 代理商： | PI7C8150B-33 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁當前第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
PI7C8150B
2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 102 of 115
July 31, 2003 – Revision 1.031
read data. Again, the PAR signal corresponds to read data from the previous data phase
cycle.
15.2.3
REPORTING PARITY ERRORS
For all address phases, if a parity error is detected, the error should be reported on the
P_SERR_L signal by asserting P_SERR_L for one cycle and then 3-stating two cycles
after the bad address. P_SERR_L can only be asserted if bit 6 and 8 in the Command
Register are both set to 1. For write data phases, a parity error should be reported by
asserting the P_PERR_L signal two cycles after the data phase and should remain asserted
for one cycle when bit 6 in the Command register is set to a 1.
The target reports any type of data parity errors during write cycles, while the master
reports data parity errors during read cycles.
Detection of an address parity error will cause the PCI-to-PCI Bridge target to not claim
the bus (P_DEVSEL_L remains inactive) and the cycle will then terminate with a Master
Abort. When the bridge is acting as master, a data parity error during a read cycle results in
the bridge master initiating a Master Abort.
15.2.4
SECONDARY IDSEL MAPPING
When PI7C8150B detects a Type 1 configuration transaction for a device connected to
the secondary, it translates the Type 1 transaction to Type 0 transaction on the downstream
interface. Type 1 configuration format uses a 5-bit field at P_AD[15:11] as a device
number. This is translated to S_AD[31:16] by PI7C8150B.
16
IEEE 1149.1 COMPATIBLE JTAG CONTROLLER
An IEEE 1149.1 compatible Test Access Port (TAP) controller and associated TAP pins
are provided to support boundary scan in PI7C8150B for board-level continuity test and
diagnostics. The TAP pins assigned are TCK, TDI, TDO, TMS and TRST_L. All digital
input, output, input/output pins are tested except TAP pins.
The IEEE 1149.1 Test Logic consists of a TAP controller, an instruction register, and
a group of test data registers including Bypass and Boundary Scan registers. The TAP
controller is a synchronous 16-state machine driven by the Test Clock (TCK) and the Test
Mode Select (TMS) pins. An independent power on reset circuit is provided to ensure the
machine is in TEST_LOGIC_RESET state at power-up. The JTAG signal lines are not
active when the PCI resource is operating PCI bus cycles.
PI7C8150B implements 3 basic instructions: BYPASS, SAMPLE/PRELOAD, and
EXTEST.
16.1
BOUNDARY SCAN ARCHITECTURE
Boundary-scan test logic consists of a boundary-scan register and support logic. These are
accessed through a Test Access Port (TAP). The TAP provides a simple serial interface
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8152B | PCI Bridge | Asynchronous 2-Port PCI Bridge |
| PI7C8154 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8154-33 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150-33 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8150BEVB | 功能描述:界面開發工具 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C8150BMA | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
| PI7C8150BMA-33 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
| PI7C8150BMAE | 功能描述:外圍驅動器與原件 - PCI 32-Bit PCI Bridge 2 Port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150BMAI | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
發布緊急采購，3分鐘左右您將得到回復。