參數資料
型號： PI7C8150A
英文描述： PCI Bridge | 2-Port PCI-to-PCI Bridge
中文描述： PCI橋| 2端口PCI至PCI橋
文件頁數： 74/115頁
文件大小： 879K
代理商： PI7C8150A
PI7C8150B
2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 74 of 115
July 31, 2003 – Revision 1.031
!
Write-1-to-clear output data field
!
Write-1-to-set signal output enable control field
!
Write-1-to-clear signal output enable control field
!
Input data field
The bottom four bits of the output enable fields control whether each GPIO signal is input
only or bi-directional. Each signal is controlled independently by a bit in each output
enable control field. If a 1 is written to the write-1-to-set field, the corresponding pin is
activated as an output. If a 1 is written to the write-1-to-clear field, the output driver is tri-
stated, and the pin is then input only. Writing zeroes to these registers has no effect. The
reset for these signals is input only.
The input data field is read only and reflects the current value of the GPIO pins. A type 0
configuration read operation to this address is used to obtain the values of these pins. All
pins can be read at any time, whether configured as input only or as bi-directional.
The output data fields also use the write-1-to-set and write-1-to-clear mode. If a 1 is
written to the write-1-to-set field and the pin is enabled as an output, the corresponding
GPIO output is driven HIGH. If a 1 is written to the write-1-to-clear field and the pin is
enabled as an output, the corresponding GPIO output is driven LOW. Writing zeros to
these registers has no effect. The value written to the output register will be driven only
when the GPIO signal is configured as bi-directional. A type 0 configuration write
operation is used to program these fields. The rest value for the output is 0.
10.2
SECONDARY CLOCK CONTROL
The PI7C8150B uses the GPIO pins and the MSK_IN signal to input a 16-bit serial data
stream. This data stream is shifted into the secondary clock control register and is used for
selectively disabling secondary clock outputs.
The serial data stream is shifted in as soon as P_RST_L is detected deasserted and the
secondary reset signal, S_RST_L, is detected asserted. The deassertion of S_RST_L is
delayed until the PI7C8150B completes shifting in the clock mask data, which takes 23
clock cycles. After that, the GPIO pins can be used as general-purpose I/O pins.
An external shift register should be used to load and shift the data. The GPIO pins are used
for shift register control and serial data input. Table 10-1
shows the operation of the GPIO
pins.
Table 10-1. GPIO Operation
GPIO Pin
Operation
GPIO[0]
GPIO[1]
GPIO[2]
Shift register clock output at 33MHz max frequency
Not used
Shift register control
0: Load
1: Shift
Not used
GPIO[3]
相關PDF資料
PDF描述
PI7C8150A-33 PCI Bridge | 2-Port PCI-to-PCI Bridge
PI7C8150B PCI Bridge | Asynchronous 2-Port PCI Bridge
PI7C8152A ENHANCED 2- PORT TO PCI BRIDGE INTEL 21152 COMPORISON
PI7C81552 ENHANCED 2-PORT PCI TO PCI BRIDGE INTEL 21152 COMPARISON
PI7C81552A ENHANCED 2-PORT PCI TO PCI BRIDGE INTEL 21152 COMPARISON
相關代理商/技術參數
參數描述
PI7C8150A-33 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Bridge | 2-Port PCI-to-PCI Bridge
PI7C8150AMA 制造商:Pericom Semiconductor Corporation 功能描述:PCI to PCI Bridge 208-Pin FQFP
PI7C8150AMA-33 制造商:Pericom Semiconductor Corporation 功能描述:PCI-to-PCI Bridge 208-Pin FQFP
PI7C8150AMAE 功能描述:外圍驅動器與原件 - PCI 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150AMAE-33 功能描述:外圍驅動器與原件 - PCI 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*