- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9546A (NXP Semiconductors N.V.) 4-channel I2C switch with reset PDF資料下載
參數資料
| 型號： | PCA9546A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 4-channel I2C switch with reset |
| 中文描述： | 4通道的I2C開關與復位 |
| 文件頁數： | 9/25頁 |
| 文件大小： | 144K |
| 代理商： | PCA9546A |
9397 750 14318
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 03 — 6 April 2005
9 of 25
Philips Semiconductors
PCA9546A
4-channel I
2
C switch with reset
8.4 Acknowledge
The number of data bytes transferred between the START and the STOP conditions from
transmitter to receiver is not limited. Each byte of eight bits is followed by one
acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter,
whereas the master generates an extra acknowledge related clock pulse.
A slave receiver which is addressed must generate an acknowledge after the reception of
each byte. Also, a master must generate an acknowledge after the reception of each byte
that has been clocked out of the slave transmitter. The device that acknowledges has to
pull down the SDA line during the acknowledge clock pulse so that the SDA line is stable
LOW during the HIGH period of the acknowledge related clock pulse; setup and hold
times must be taken into account.
A master receiver must signal an end of data to the transmitter by not generating an
acknowledge on the last byte that has been clocked out of the slave. In this event, the
transmitter must leave the data line HIGH to enable the master to generate a STOP
condition.
Fig 10. System configuration
002aaa966
MASTER
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER/
RECEIVER
SDA
SCL
I
2
C
MULTIPLEXER
SLAVE
Fig 11. Acknowledgement on the I
2
C-bus
002aaa987
S
START
condition
9
8
2
1
clock pulse for
acknowledgement
not acknowledge
acknowledge
data output
by transmitter
data output
by receiver
SCL from master
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9546 | 4-channel I2C switch with reset |
| PCA9546D | 4-channel I2C switch with reset |
| PCA9546PW | 4-channel I2C switch with reset |
| PCA9549 | Octal bus switch with individually I2C-bus controlled enables |
| PCA9555N | 16-bit I2C and SMBus I/O port with interrupt |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9546A_1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_3 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546ABS | 制造商:NXP Semiconductors 功能描述: |
| PCA9546ABS,118 | 功能描述:多路器開關 IC I2C SWITCH 4CH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。