- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9546A (NXP Semiconductors N.V.) 4-channel I2C switch with reset PDF資料下載
參數資料
| 型號： | PCA9546A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 4-channel I2C switch with reset |
| 中文描述： | 4通道的I2C開關與復位 |
| 文件頁數： | 8/25頁 |
| 文件大?。?/td> | 144K |
| 代理商： | PCA9546A |
9397 750 14318
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 03 — 6 April 2005
8 of 25
Philips Semiconductors
PCA9546A
4-channel I
2
C switch with reset
More Information can be found in Application Note AN262: PCA954X family of I2C/SMBus
multiplexers and switches
8.
Characteristics of the I
2
C-bus
The I
2
C-bus is for 2-way, 2-line communication between different ICs or modules. The two
lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be
connected to a positive supply via a pull-up resistor when connected to the output stages
of a device. Data transfer may be initiated only when the bus is not busy.
8.1 Bit transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the HIGH period of the clock pulse as changes in the data line at this time
will be interpreted as control signals (see
Figure 8
).
8.2 START and STOP conditions
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW
transition of the data line while the clock is HIGH is defined as the START condition (S).
A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP
condition (P) (see
Figure 9
).
8.3 System configuration
A device generating a message is a ‘transmitter’, a device receiving is the ‘receiver’. The
device that controls the message is the ‘master’ and the devices which are controlled by
the master are the ‘slaves’ (see
Figure 10
).
Fig 8.
Bit transfer
mba607
data line
stable;
data valid
change
of data
allowed
SDA
SCL
Fig 9.
Definition of START and STOP conditions
mba608
SDA
SCL
P
STOP condition
SDA
SCL
S
START condition
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9546 | 4-channel I2C switch with reset |
| PCA9546D | 4-channel I2C switch with reset |
| PCA9546PW | 4-channel I2C switch with reset |
| PCA9549 | Octal bus switch with individually I2C-bus controlled enables |
| PCA9555N | 16-bit I2C and SMBus I/O port with interrupt |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9546A_1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_3 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546ABS | 制造商:NXP Semiconductors 功能描述: |
| PCA9546ABS,118 | 功能描述:多路器開關 IC I2C SWITCH 4CH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。