- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9546A (NXP Semiconductors N.V.) 4-channel I2C switch with reset PDF資料下載
參數資料
| 型號： | PCA9546A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 4-channel I2C switch with reset |
| 中文描述： | 4通道的I2C開關與復位 |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 144K |
| 代理商： | PCA9546A |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁
9397 750 14318
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 03 — 6 April 2005
7 of 25
Philips Semiconductors
PCA9546A
4-channel I
2
C switch with reset
7.3 RESET input
The RESET input is an active LOW signal which may be used to recover from a bus fault
condition. By asserting this signal LOW for a minimum of t
WL
, the PCA9546A will reset its
registers and I
2
C-bus state machine and will deselect all channels. The RESET input must
be connected to V
DD
through a pull-up resistor.
7.4 Power-on reset
When power is applied to V
DD
, an internal Power-On Reset (POR) holds the PCA9546A in
a reset condition until V
DD
has reached V
POR
. At this point, the reset condition is released
and the PCA9546A registers and I
2
C-bus state machine are initialized to their default
states—all zeroes—causing all the channels to be deselected. Thereafter, V
DD
must be
lowered below 0.2 V to reset the device.
7.5 Voltage translation
The pass gate transistors of the PCA9546A are constructed such that the V
DD
voltage can
be used to limit the maximum voltage that will be passed from one I
2
C-bus to another.
Figure 7
shows the voltage characteristics of the pass gate transistors (note that the graph
was generated using the data specified in
Section 11 “Static characteristics”
of this data
sheet). In order for the PCA9546A to act as a voltage translator, the V
o(sw)
voltage should
be equal to, or lower than the lowest bus voltage. For example, if the main bus was
running at 5 V, and the downstream buses were 3.3 V and 2.7 V, then V
o(sw)
should be
equal to or below 2.7 V to effectively clamp the downstream bus voltages. Looking at
Figure 7
, we see that V
o(sw)(max)
will be at 2.7 V when the PCA9546A supply voltage is
3.5 V or lower, so the PCA9546A supply voltage could be set to 3.3 V. Pull-up resistors
can then be used to bring the bus voltages to their appropriate levels (see
Figure 14
).
(1) maximum
(2) typical
(3) minimum
Fig 7.
Pass gate voltage versus supply voltage
V
DD
(V)
2.0
5.5
4.5
3.0
4.0
002aaa964
3.0
2.0
4.0
5.0
V
o(sw)
(V)
1.0
3.5
5.0
2.5
(1)
(2)
(3)
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9546 | 4-channel I2C switch with reset |
| PCA9546D | 4-channel I2C switch with reset |
| PCA9546PW | 4-channel I2C switch with reset |
| PCA9549 | Octal bus switch with individually I2C-bus controlled enables |
| PCA9555N | 16-bit I2C and SMBus I/O port with interrupt |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9546A_1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546A_3 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus SWITCH WITH RESET FUNCTION |
| PCA9546ABS | 制造商:NXP Semiconductors 功能描述: |
| PCA9546ABS,118 | 功能描述:多路器開關 IC I2C SWITCH 4CH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。