- 您現在的位置：買賣IC網 > PDF目錄367808 > PCA9506 (NXP Semiconductors N.V.) 40-bit I2C-bus I/O port with RESET, OE, and INT PDF資料下載
參數資料
| 型號： | PCA9506 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 40-bit I2C-bus I/O port with RESET, OE, and INT |
| 中文描述： | 40位I2C總線的I / O端口復位，光電，和INT |
| 文件頁數： | 27/30頁 |
| 文件大?。?/td> | 145K |
| 代理商： | PCA9506 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁
9397 750 14939
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 — 14 February 2006
27 of 30
Philips Semiconductors
PCA9506
40-bit I
2
C-bus I/O port with RESET, OE, and INT
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250
°
C
or 265
°
C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
16.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270
°
C and 320
°
C.
16.5 Package related soldering information
[1]
For more detailed information on the BGA packages refer to the (LF)BGA Application Note(AN01026);
order a copy from your Philips Semiconductors sales office.
Table 12:
Package
[1]
Suitability of surface mount IC packages for wave and reflow soldering methods
Soldering method
Wave
BGA, HTSSON..T
[3]
, LBGA, LFBGA, SQFP,
SSOP..T
[3]
, TFBGA, VFBGA, XSON
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
PLCC
[5]
, SO, SOJ
LQFP, QFP, TQFP
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L
[8]
, PMFP
[9]
, WQCCN..L
[8]
Reflow
[2]
suitable
not suitable
not suitable
[4]
suitable
suitable
not recommended
[5] [6]
not recommended
[7]
not suitable
suitable
suitable
suitable
not suitable
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9509 | Level translating I2C-bus/SMBus repeater |
| PCA9510A | Hot swappable I2C-bus and SMBus bus buffer |
| PCA9511A | Hot swappable I2C-bus and SMBus bus buffer |
| PCA9511DP | Hot swappable I2C and SMBus bus buffer |
| PCA9510 | Hot swappable I2C and SMBus bus buffer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9506BS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:40-bit I2C-bus I/O port with RESET, OE and INT |
| PCA9506BS,118 | 功能描述:接口-I/O擴展器 I/O EXPANDER I2C RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9506BS,118-CUT TAPE | 制造商:NXP 功能描述:PCA9506 Series 40-Bit I2C-Bus I/O Port with RESET OE and INT - HVQFN - 56 |
| PCA9506DGG | 功能描述:接口-I/O擴展器 I/O EXPANDER I2C RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9506DGG,512 | 功能描述:接口-I/O擴展器 I/O EXPANDER I2C RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。