參數資料
型號： P89V660FBC,557
廠商： NXP Semiconductors
文件頁數： 66/90頁
文件大?。?/td> 0K
描述： IC 80C51 MCU FLASH 16K 44-TQFP
產品培訓模塊： Migrating from 8/16-Bit MCUs to 32-Bit ARMs
標準包裝： 800
系列： 89V
核心處理器： 8051
芯體尺寸： 8-位
速度： 40MHz
連通性： I²C，SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 36
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： 閃存
RAM 容量： 512 x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-TQFP
包裝： 托盤
產品目錄頁面： 706 (CN2011-ZH PDF)
配用： 622-1001-ND - USB IN-CIRCUIT PROG 80C51ISP
其它名稱： 568-2433
935280829557
P89V660FBC
P89V660_662_664
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3.1 — 17 October 2011
69 of 90
NXP Semiconductors
P89V660/662/664
80C51 with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
6.13.1 Idle mode
Idle mode is entered setting the IDL bit in the PCON register. In Idle mode, the program
counter is stopped. The system clock continues to run and all interrupts and peripherals
remain active. The on-chip RAM and the special function registers hold their data during
this mode.
The device exits Idle mode through either a system interrupt or a hardware reset. Exiting
Idle mode via system interrupt, the start of the interrupt clears the IDL bit and exits Idle
mode. After exit the Interrupt Service Routine, the interrupted program resumes execution
beginning at the instruction immediately following the instruction which invoked the Idle
mode. A hardware reset starts the device similar to a power-on reset.
6.13.2 Power-down mode
The Power-down mode is entered by setting the PD bit in the PCON register. In the
Power-down mode, the clock is stopped and external interrupts are active for level
sensitive interrupts only. SRAM contents are retained during Power-down, the minimum
VDD level is 2.0 V.
The device exits Power-down mode through either an enabled external level sensitive
interrupt or a hardware reset. The start of the interrupt clears the PD bit and exits
Power-down. Holding the external interrupt pin low restarts the oscillator, the signal must
hold low at least 1024 clock cycles before bringing back high to complete the exit. Upon
interrupt signal restored to logic VIH, the interrupt service routine program execution
resumes beginning at the instruction immediately following the instruction which invoked
Power-down mode. A hardware reset starts the device similar to power-on reset.
To exit properly out of Power-down, the reset or external interrupt should not be executed
before the VDD line is restored to its normal operating voltage. Be sure to hold VDD voltage
long enough at its normal operating level for the oscillator to restart and stabilize (normally
less than 10 ms).
Table 67.
Power-saving modes
Mode
Initiated by
State of MCU
Exited by
Idle mode
Software (Set IDL bit in
PCON) MOV PCON, #01H
CLK is running. Interrupts,
serial port and timers/counters
are active. Program Counter is
stopped. ALE and PSEN
signals at a HIGH-state during
Idle. All registers remain
unchanged.
Enabled interrupt or hardware reset. Start of
interrupt clears IDL bit and exits Idle mode,
after the ISR RETI instruction, program
resumes execution beginning at the
instruction following the one that invoked
Idle mode. A hardware reset restarts the
device similar to a power-on reset.
Power-down
mode
Software (Set PD bit in
PCON) MOV PCON, #02H
CLK is stopped. On-chip SRAM
and SFR data is maintained.
ALE and PSEN signals at a
LOW-state during power-down.
External Interrupts are only
active for level sensitive
interrupts, if enabled.
Enabled external level sensitive interrupt or
hardware reset. Start of interrupt clears PD
bit and exits Power-down mode, after the
ISR RETI instruction program resumes
execution beginning at the instruction
following the one that invoked Power-down
mode. A hardware reset restarts the device
similar to a power-on reset.
相關PDF資料
PDF描述
P89V662FBC,557 IC 80C51 MCU FLASH 32K 44-TQFP
PIC32MX130F064B-I/SO IC MCU 32BIT 64KB FLASH 28-SOIC
PIC32MX220F032D-I/ML IC MCU 32BIT 32KB FLASH 44QFN
PIC18LF26K80-I/MM MCU PIC 64KB FLASH 28QFN
PIC18F26K80-I/MM MCU PIC 64KB FLASH 28QFN
相關代理商/技術參數
參數描述
P89V662 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V662FA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V662FA,512 功能描述:8位微控制器 -MCU 80C51 32K FL / 1K RM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89V662FBC 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V662FBC,557 功能描述:8位微控制器 -MCU 80C51 32K FL / 1K RM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*